@prefix rdf: . @prefix owl: . @prefix rdfs: . @prefix xml: . @prefix xsd: . a owl:Ontology; "urn:iso:std:iec:61970-600-2:ed-1", "urn:iso:std:iec:61970-301:ed-7:amd1", "urn:iso:std:iec:61970-401:draft:ed-1", "file://CIM17-2_CGMES31v01_PROF-20v03_NC25v25_MS10v12_DES10v01.eap", "file://iec61970cim17v40_iec61968cim13v13a_iec62325cim03v17a.eap", "urn:iso:std:iec:61970-501:draft:ed-2"; "ENTSO-E CIM WG NC project"@en; "This vocabulary is describing the state instruction schedule profile."@en; "a7f46528-9468-44cb-8695-bd023bdcea40"; "SIS"; "en-GB"; "https://www.apache.org/licenses/LICENSE-2.0"@en; "2026-08-05"^^xsd:date; owl:priorVersion ; "ENTSO-E"@en; "ENTSO-E"@en; "vocabulary"@en; "State instruction schedule vocabulary"@en; owl:versionIRI ; owl:versionInfo "2.5.0"@en . a ; rdfs:comment "Automatic Frequency Restoration Reserve (aFRR). Automatically activated balancing reserve used to restore system frequency and scheduled interchanges under automatic generation control (AGC)."; rdfs:label "aFRR"@en; "enum" . a ; rdfs:comment "Frequency Containment Reserve (FCR). Automatically activated reserve that provides immediate frequency containment following small frequency deviations or disturbances."; rdfs:label "fcr"@en; "enum" . a ; rdfs:comment "Manual Frequency Restoration Reserve (mFRR). Manually activated balancing reserve used to restore system balance following activation by the system operator."; rdfs:label "mFRR"@en; "enum" . a ; rdfs:comment "Time series is actual data. The values represent measured or calculated values that represent the actual behaviour. "; rdfs:label "actual"@en; "enum" . a ; rdfs:comment "Time series is forecast data. The values represent the result of scientific predictions based on historical time stamped data."; rdfs:label "forecast"@en; "enum" . a ; rdfs:comment "Time series is hindcast data. The value represent probable past (historic) condition given by calculation done using actual values. For instance, determine the among of wind based on the energy produced by wind. However, hindcast is typical the result of a simulated forecasts for historical periods."; rdfs:label "hindcast"@en; "enum" . a ; rdfs:comment "Time series is schedule data. The values represent the result of a committed and plan forecast data that has been through a quality control and could incur penalty when not followed."; rdfs:label "schedule"@en; "enum" . a rdfs:Class; ; rdfs:comment """The AC emulation control function is used when AC emulation model is activated for a DC system. It consists in computing the active power set point of the DC system as a function of the voltage angle difference between both points of common coupling with the AC network in order to mimic the behavior of an AC transmission line. This control mode enables the automatic adjustment of the active power reference following variations of the AC system operational point. The setpoint of the DC system is calculated by Psetpoint=Pref+Kdc*(angle1-angle2), where - Pref is the existing active power setpoint; - Kdc is the control system gain and - angle1 and angle2 are the phase angle measurement (measured at points of common coupling with the AC network) respectively at the side 1 and 2 of the DC system."""; rdfs:label "ACEmulationControlFunction"@en; "NC" . a rdfs:Class; ; rdfs:comment "The schedule for ACEmulationControlFunction."; rdfs:label "ACEmulationControlFunctionSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "AC emulation control function value for a given point in time."; rdfs:label "ACEmulationControlFunctionTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Product of RMS value of the voltage and the RMS value of the in-phase component of the current."; rdfs:label "ActivePower"@en; "CIMDatatype" . a rdfs:Class; ; rdfs:comment "Active power control function is a function block that calculates operating point of the controlled equipment to achieve the target active power."; rdfs:label "ActivePowerControlFunction"@en; "NC" . a rdfs:Class; ; rdfs:comment "The schedule for ActivePowerControlFunction."; rdfs:label "ActivePowerControlFunctionSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Active power control function value for a given point in time."; rdfs:label "ActivePowerControlFunctionTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Measurement of angle in degrees."; rdfs:label "AngleDegrees"@en; "CIMDatatype" . a rdfs:Class; ; rdfs:comment """A resource representation for a specific balancing reserve product, associated with either a scheduling area or a tie corridor, and used to represent reserve capability made available to a control area for market and operational purposes. Note: An AreaReserveResource shall be associated with either a SchedulingArea or a TieCorridor, but not both. When associated with a SchedulingArea, the resource represents reserve capability made available within that area context. When associated with a TieCorridor, the resource represents reserve capability provided across an inter-area connection to support a control area other than the one in which the underlying resource is located. A single physical or logical resource (for example a GeneratingUnit, HydroPump, PowerElectronicsUnit, or equivalent) may be represented by multiple AreaReserveResource instances, each corresponding to a different balancing reserve product (e.g. FCR, aFRR, mFRR)."""; rdfs:label "AreaReserveResource"@en; "NC" . a rdfs:Class; ; rdfs:comment "Regular schedule for area reserve resource ."; rdfs:label "AreaReserveResourceRegularSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Schedule for area reserve resource ."; rdfs:label "AreaReserveResourceSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Area reserve resource for a given point in time."; rdfs:label "AreaReserveResourceTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment """Assessed element is a network element for which the electrical state is evaluated in the regional or cross-regional process and which value is expected to fulfil regional rules function of the operational security limits. The measurements and limits are as defined in the steady state hypothesis."""; rdfs:label "AssessedElement"@en; "NC"; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Regular schedule for assessed element."; rdfs:label "AssessedElementRegularSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Assessed element instruction value at a given point in time."; rdfs:label "AssessedElementRegularTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Schedule for assessed element."; rdfs:label "AssessedElementSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Assessed element instruction value at a given point in time."; rdfs:label "AssessedElementTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Combination of an assessed element and a contingency."; rdfs:label "AssessedElementWithContingency"@en; "NC" . a rdfs:Class; ; rdfs:comment "Combination of an assessed element and a remedial action"; rdfs:label "AssessedElementWithRemedialAction"@en; "NC" . a rdfs:Class; ; rdfs:comment "Automation function is a collection of functional block or other automation function that can be executed as a work cycle program as part of an automated system."; rdfs:label "AutomationFunction"@en; "NC" . a rdfs:Class; ; rdfs:comment "Availability instruction value at a given point in time."; rdfs:label "AvailabilityTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Classification of the balancing reserve product represented by an AreaReserveResource. The kind identifies the reserve service for which the associated resource has been qualified and made available."; rdfs:label "BalancingReserveKind"@en; , "NC" . a rdfs:Class; ; rdfs:comment "Operational limit on current applicable for base case. "; rdfs:label "BaseCaseCurrentLimit"@en; "NC" . a rdfs:Class; ; rdfs:comment "The schedule for a base case current limit."; rdfs:label "BaseCaseCurrentLimitSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Base case current limit at a given point in time."; rdfs:label "BaseCaseCurrentLimitTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Time series that has irregular points in time."; rdfs:label "BaseIrregularTimeSeries"@en; "NC"; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Time series that has regular points in time."; rdfs:label "BaseRegularIntervalSchedule"@en; "NC"; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Time series of values at points in time."; rdfs:label "BaseTimeSeries"@en; "NC"; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Kind of time series. "; rdfs:label "BaseTimeSeriesKind"@en; , "NC" . a rdfs:Class; ; rdfs:comment "A type with the value space \"true\" and \"false\"."; rdfs:label "Boolean"@en; "Primitive" . a rdfs:Class; ; rdfs:comment """A geographically defined area characterised according to a climate classification and used as a spatial reference for representative meteorological, hydrological and marine conditions relevant to energy production, consumption and resource availability. Note: ClimateZone provides selected climatological normal values as structured information and may reference time series for detailed climate, weather, hydrological and marine data. A normal value represents a climatological reference condition for the area. Time series may represent observed, historical, modelled, forecast, scenario or climatological data. Reference period, scenario, source, calculation method and other provenance information are represented separately. ClimateZone may be used to associate energy resources and energy-system studies with climate-dependent conditions such as temperature, wind, solar irradiance, precipitation, snow, hydro inflow, extreme weather, waves, sea ice and sea currents. Example: Climate study zones defined in the Pan-European Climate Database (PECD) for European energy-system modelling."""; rdfs:label "ClimateZone"@en; "NC" . a rdfs:Class; ; rdfs:comment "Regular schedule for ClimateZone."; rdfs:label "ClimateZoneRegularSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "The irregular schedule for the ClimateZone."; rdfs:label "ClimateZoneSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Climate zone value at a given point in time."; rdfs:label "ClimateZoneTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "The parts of the AC power system that are designed to carry current or that are conductively connected through terminals."; rdfs:label "ConductingEquipment"@en; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "An event threatening system reliability, consisting of one or more contingency elements."; rdfs:label "Contingency"@en . a rdfs:Class; ; rdfs:comment "The schedule for Contingency."; rdfs:label "ContingencySchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Contingency instruction value at a given point in time."; rdfs:label "ContingencyTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Combination of a contingency and a remedial action. ContingencyWithRemedialAction shall not be instantiated for preventive RemedialAction (RemedialAction.kind equals RemedialActionKind.preventive)."; rdfs:label "ContingencyWithRemedialAction"@en; "NC" . a rdfs:Class; ; rdfs:comment """Number of discrete occurrences or events per unit area. Note: Intended for spatial event densities such as lightning density. A new UnitSymbol countPerm2 is required if this quantity is represented as a CIMDatatype with an explicit unit."""; rdfs:label "CountPerArea"@en; "NC", "CIMDatatype", "new" . a rdfs:Class; ; rdfs:comment "Combination of an assessed element and one or more bidding zone border that are affected by the assessment."; rdfs:label "CrossBorderRelevance"@en; "NC" . a rdfs:Class; ; rdfs:comment "Monetary currencies. ISO 4217 standard including 3-character currency code."; rdfs:label "Currency"@en; . a rdfs:Class; ; rdfs:comment "Current control function is a function block that calculates the operating point of the controlled equipment to achieve the target current."; rdfs:label "CurrentControlFunction"@en; "NC" . a rdfs:Class; ; rdfs:comment "The schedule for CurrentControlFunction."; rdfs:label "CurrentControlFunctionSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Current control function value for a given point in time."; rdfs:label "CurrentControlFunctionTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Current droop control function is a function block that calculates the operating point of the controlled equipment to achieve the target current."; rdfs:label "CurrentDroopControlFunction"@en; "NC" . a rdfs:Class; ; rdfs:comment "The schedule for CurrentDroopControlFunction."; rdfs:label "CurrentDroopControlFunctionSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Current droop control function value for a given point in time."; rdfs:label "CurrentDroopControlFunctionTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Electrical current with sign convention: positive flow is out of the conducting equipment into the connectivity node. Can be both AC and DC."; rdfs:label "CurrentFlow"@en; "CIMDatatype" . a rdfs:Class; ; rdfs:comment "Direct current active power control function is a function block that calculates operating point of the controlled equipment to achieve the target active power."; rdfs:label "DCActivePowerControlFunction"@en; "NC" . a rdfs:Class; ; rdfs:comment "The schedule for DCActivePowerControlFunction."; rdfs:label "DCActivePowerControlFunctionSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Direct current active power control function value for a given point in time."; rdfs:label "DCActivePowerControlFunctionTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "DC current control function is a function block that calculates the operating point of the controlled equipment to achieve the target current."; rdfs:label "DCCurrentControlFunction"@en; "NC" . a rdfs:Class; ; rdfs:comment "The schedule for DCCurrentControlFunction."; rdfs:label "DCCurrentControlFunctionSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "DC current control function value for a given point in time."; rdfs:label "DCCurrentControlFunctionTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "This class represents direct current equivalent injections (generation or load). "; rdfs:label "DCEquivalentInjection"@en; "NC" . a rdfs:Class; ; rdfs:comment "Direct current extinction angle control function is a function block that calculates operating point of the controlled equipment to achieve the target extinction angle."; rdfs:label "DCExtinctionAngleControlFunction"@en; "NC" . a rdfs:Class; ; rdfs:comment "The schedule for DCExtinctionAngleControlFunction."; rdfs:label "DCExtinctionAngleControlFunctionSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Direct current extinction angle control function value for a given point in time."; rdfs:label "DCExtinctionAngleControlFunctionTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Direct current firing angle control function is a function block that calculates operating point of the controlled equipment to achieve the target firing angle."; rdfs:label "DCFiringAngleControlFunction"@en; "NC" . a rdfs:Class; ; rdfs:comment "The schedule for DCFiringAngleControlFunction."; rdfs:label "DCFiringAngleControlFunctionSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Direct current firing angle control function value for a given point in time."; rdfs:label "DCFiringAngleControlFunctionTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment """The direct current (DC) system pole (IEC 60633) is part of a DC system consisting of all the equipment in the DC substations and the interconnecting transmission lines, if any, which during normal operation exhibit a common direct voltage polarity with respect to earth. It includes active power, reactive power and participation factor to be able to schedule top down (using DCTieCorridor and participation factor to provide schedule on the DCPole) and bottom up (aggregation of DCPole to DCTieCorridor). Only one approach can be used at a time."""; rdfs:label "DCPole"@en; "NC" . a rdfs:Class; ; rdfs:comment "Direct current pulse width modulation control function is a function block that calculates operating point of the controlled equipment to achieve the target pulse width modulation."; rdfs:label "DCPulseWidthModulationControlFunction"@en; "NC" . a rdfs:Class; ; rdfs:comment "The schedule for DCPulseWidthModulationControlFunction."; rdfs:label "DCPulseWidthModulationControlFunctionSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Direct current pulse width modulation control function value for a given point in time."; rdfs:label "DCPulseWidthModulationControlFunctionTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "DC voltage control function is a function block that calculate the operating point of the controlled equipment to achieve the target voltage."; rdfs:label "DCVoltageControlFunction"@en; "NC" . a rdfs:Class; ; rdfs:comment "The schedule for DCVoltageControlFunction."; rdfs:label "DCVoltageControlFunctionSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "DC voltage control function value for a given point in time."; rdfs:label "DCVoltageControlFunctionTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Date as \"yyyy-mm-dd\", which conforms with ISO 8601. UTC time zone is specified as \"yyyy-mm-ddZ\". A local timezone relative UTC is specified as \"yyyy-mm-dd(+/-)hh:mm\"."; rdfs:label "Date"@en; "Primitive" . a rdfs:Class; ; rdfs:comment "Date and time as \"yyyy-mm-ddThh:mm:ss.sss\", which conforms with ISO 8601. UTC time zone is specified as \"yyyy-mm-ddThh:mm:ss.sssZ\". A local timezone relative UTC is specified as \"yyyy-mm-ddThh:mm:ss.sss-hh:mm\". The second component (shown here as \"ss.sss\") could have any number of digits in its fractional part to allow any kind of precision beyond seconds."; rdfs:label "DateTime"@en; "Primitive" . a rdfs:Class; ; rdfs:comment "The kind of day to be included in a regular schedule."; rdfs:label "DayOfWeekKind"@en; , "NC" . a rdfs:Class; ; rdfs:comment "Decimal is the base-10 notational system for representing real numbers."; rdfs:label "Decimal"@en; "Primitive" . a rdfs:Class; ; rdfs:comment """The kind of dependency constraint defined between the dependee and dependent peer objects. Note: The dependee is the peer object upon which another peer object depends. The dependent is the peer object whose temporal or operational behaviour is constrained by the dependee. Although dependee is not a commonly used English term, it is used here to distinguish this relationship from a parent-child hierarchy, as both objects are peer instances of the same class."""; rdfs:label "DependencyConstraintKind"@en; , "NC" . a rdfs:Class; ; rdfs:comment "Duration as \"PnYnMnDTnHnMnS\" which conforms to ISO 8601, where nY expresses a number of years, nM a number of months, nD a number of days. The letter T separates the date expression from the time expression and, after it, nH identifies a number of hours, nM a number of minutes and nS a number of seconds. The number of seconds could be expressed as a decimal number, but all other numbers are integers."; rdfs:label "Duration"@en; "Primitive" . a rdfs:Class; ; rdfs:comment "Enabling instruction value at a given point in time."; rdfs:label "EnablingTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "The energy block order is a block (an amount) of energy that forms the sequence of orders that are going to be distributed to an energy block component."; rdfs:label "EnergyBlockOrder"@en; "NC" . a rdfs:Class; ; rdfs:comment "A connection of energy generation or consumption on the power system model."; rdfs:label "EnergyConnection"@en; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment """Generic user of energy - a point of consumption on the power system model. EnergyConsumer.pfixed, .qfixed, .pfixedPct and .qfixedPct have meaning only if there is no LoadResponseCharacteristic associated with EnergyConsumer or if LoadResponseCharacteristic.exponentModel is set to False."""; rdfs:label "EnergyConsumer"@en . a rdfs:Class; ; rdfs:comment """An aggregation of energy resources having common energy characteristics for which installed, available, or effective capacity is represented. Note: EnergyResourceGroupCapacity groups energy resources for capacity modelling, forecasting, scenario analysis and aggregation. The group may be characterised by an energy kind, energy source, technology, location, scenario, weather condition or other modelling context. The aggregated capacity may be represented by static values or by time-series values describing forecast, scheduled, actual or hindcast conditions. An EnergyComponent represents the part of an aggregated value associated with a particular underlying unit or resource. The aggregated value of the EnergyResourceGroupCapacity may therefore be distributed among its associated EnergyComponents, for example in proportion to the capability of the corresponding units or according to an ordered block-based allocation. Weather or other environmental information may be referenced where it is relevant to the capacity or availability of the grouped resources/"""; rdfs:label "EnergyResourceGroupCapacity"@en; "NC" . a rdfs:Class; ; rdfs:comment "Regular schedule for EnergyResourceGroupCapacity."; rdfs:label "EnergyResourceGroupCapacityRegularSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "The irregular schedule for the energy resource capacity group."; rdfs:label "EnergyResourceGroupCapacitySchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Energy resource group capacity value at a given point in time."; rdfs:label "EnergyResourceGroupCapacityTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Kind of energy scenario."; rdfs:label "EnergyScenarioKind"@en; , "NC" . a rdfs:Class; ; rdfs:comment "A generic equivalent for an energy supplier on a transmission or distribution voltage level."; rdfs:label "EnergySource"@en . a rdfs:Class; ; rdfs:comment "The parts of a power system that are physical devices, electronic or mechanical."; rdfs:label "Equipment"@en; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "This class represents equivalent injections (generation or load). Voltage regulation is allowed only at the point of connection."; rdfs:label "EquivalentInjection"@en . a rdfs:Class; ; rdfs:comment "This class represents the external network and it is used for IEC 60909 calculations."; rdfs:label "ExternalNetworkInjection"@en . a rdfs:Class; ; rdfs:comment "A floating point number. The range is unspecified and not limited."; rdfs:label "Float"@en; "Primitive" . a rdfs:Class; ; rdfs:comment "Cycles per second."; rdfs:label "Frequency"@en; "CIMDatatype" . a rdfs:Class; ; rdfs:comment "Frequency control function is a function block that calculate the operating point of the controlled equipment to achieve the target frequency."; rdfs:label "FrequencyControlFunction"@en; "NC" . a rdfs:Class; ; rdfs:comment "The schedule for FrequencyControlFunction."; rdfs:label "FrequencyControlFunctionSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Frequency control function value for a given point in time."; rdfs:label "FrequencyControlFunctionTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Fuel storage. e.g. pile of coal that can be shared between multiple thermal generating units."; rdfs:label "FuelStorage"@en; "NC" . a rdfs:Class; ; rdfs:comment "Fuel storage schedule for elements."; rdfs:label "FuelStorageSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Fuel storage values for a given point in time."; rdfs:label "FuelStorageTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Function block is a function described as a set of elementary blocks. The blocks describe the function between input variables and output variables."; rdfs:label "FunctionBlock"@en; "NC" . a rdfs:Class; ; rdfs:comment "Input pin for a logical gate. The condition described in the input pin gives a logical true or false. The result from measurement and calculation are converted to a true or false."; rdfs:label "GateInputPin"@en; "NC" . a rdfs:Class; ; rdfs:comment "A single or set of synchronous machines for converting mechanical power into alternating-current power. For example, individual machines within a set may be defined for scheduling purposes while a single control signal is derived for the set. In this case there would be a GeneratingUnit for each member of the set and an additional GeneratingUnit corresponding to the set."; rdfs:label "GeneratingUnit"@en . a rdfs:Class; ; rdfs:comment "The schedule for the availability of elements."; rdfs:label "GenericAvailableSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "The schedule for the enabling of elements."; rdfs:label "GenericEnablingSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Schedule for sequence."; rdfs:label "GenericSequenceSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Time series represent irregular generic value at given points in time. The type of value is given by the reference association. "; rdfs:label "GenericValueSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Generic value for a given point in time."; rdfs:label "GenericValueTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment """Grid power capacity defines the active power capacity that can be imported, exported, generated, consumed, or transferred within a defined power system area, or a combination of multiple areas (e.g. a bidding zone), considering relevant grid constraints required for secure and reliable operation. Note: Grid power capacity represents a power system or network-constrained capacity, not the technical installed capacity of individual resources or groups of resources. It may describe limits on generation, consumption, import, export, or power transfer resulting from operational security limits, network constraints, capacity allocation, forecasted grid availability, planned outages, remedial actions, or market-relevant transmission limitations."""; rdfs:label "GridPowerCapacity"@en; "NC" . a rdfs:Class; ; rdfs:comment "Regular schedule for GridPowerCapacity."; rdfs:label "GridPowerCapacityRegularSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "The irregular schedule for the capacity."; rdfs:label "GridPowerCapacitySchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Capacity instruction value at a given point in time."; rdfs:label "GridPowerCapacityTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Grid state alteration is a change of values describing state (operating point) of one element in the grid model compared to the base case."; rdfs:label "GridStateAlteration"@en; "NC" . a rdfs:Class; ; rdfs:comment "Schedule for a grid state alteration."; rdfs:label "GridStateAlterationSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Grid state alteration at a given point in time."; rdfs:label "GridStateAlterationTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Defines the intensity applied for a given grid state alteration. It is primarily used in exchanges related to the remedial action schedule. The value provided by the schedule replaces the value of the attribute to which the schedule refers to."; rdfs:label "GridStateIntensitySchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Pattern of hourly period in a day with the same kind of intensity."; rdfs:label "HourPattern"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Period of hours in a day."; rdfs:label "HourPeriod"@en; "NC", . a rdfs:Class; ; rdfs:comment "Time specified in hours."; rdfs:label "Hours"@en; "CIMDatatype" . a rdfs:Class; ; rdfs:comment "A synchronous motor-driven pump, typically associated with a pumped storage plant."; rdfs:label "HydroPump"@en . a rdfs:Class; ; rdfs:comment """An IRI (Internationalized Resource Identifier) within an RDF graph is a Unicode string that conforms to the syntax defined in RFC 3987. The primitive is serialized as rdf:resource in RDFXML. IRIs in the RDF abstract syntax must be absolute, and may contain a fragment identifier. IRI equality: Two IRIs are equal if and only if they are equivalent under Simple String Comparison according to section 5.1 of [RFC3987]. Further normalization must not be performed when comparing IRIs for equality. IRIs are a generalization of URIs [RFC3986] that permits a wider range of Unicode characters. Every absolute URI and URL is an IRI, but not every IRI is an URI. When IRIs are used in operations that are only defined for URIs, they must first be converted according to the mapping defined in section 3.1 of [RFC3987]. A notable example is retrieval over the HTTP protocol. The mapping involves UTF-8 encoding of non-ASCII characters, %-encoding of octets not allowed in URIs, and Punycode-encoding of domain names."""; rdfs:label "IRI"@en; "Primitive", "profcim" . a rdfs:Class; ; rdfs:comment "This is a root class to provide common identification for all classes needing identification and naming attributes."; rdfs:label "IdentifiedObject"@en . a rdfs:Class; ; rdfs:comment "Ratio of voltage to current."; rdfs:label "Impedance"@en; "CIMDatatype" . a rdfs:Class; ; rdfs:comment "Impedance control function is a function block that calculates the operating point of the controlled equipment to achieve the target impedance."; rdfs:label "ImpedanceControlFunction"@en; "NC" . a rdfs:Class; ; rdfs:comment "The schedule for ImpedanceControlFunction."; rdfs:label "ImpedanceControlFunctionSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Impedance control function value for a given point in time."; rdfs:label "ImpedanceControlFunctionTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Infeed limit set constraints fed in to the network by two or more terminals."; rdfs:label "InfeedLimit"@en; "NC" . a rdfs:Class; ; rdfs:comment "The schedule for an infeed limit."; rdfs:label "InfeedLimitSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Infeed limit at a given point in time."; rdfs:label "InfeedLimitTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "An integer number. The range is unspecified and not limited."; rdfs:label "Integer"@en; "Primitive" . a rdfs:Class; ; rdfs:comment """Power carried by electromagnetic radiation incident on a surface per unit area. Note: Intended for solar irradiance values such as global, direct and diffuse solar irradiance."""; rdfs:label "Irradiance"@en; "NC", "CIMDatatype", "new" . a rdfs:Class; ; rdfs:comment "Unit of length. It shall be a positive value or zero."; rdfs:label "Length"@en; "CIMDatatype" . a rdfs:Class; ; rdfs:comment "Identifies the direction of activation or reserve provision for a market regulation product or instrument (e.g., aFRR, mFRR, FCR). It expresses how the service affects the system balance — by increasing or decreasing net generation or consumption."; rdfs:label "MarketRegulationDirectionKind"@en; , "NC" . a rdfs:Class; ; rdfs:comment "MonthDay format as \"--mm-dd\", which conforms with XSD data type gMonthDay."; rdfs:label "MonthDay"@en; "Primitive" . a rdfs:Class; ; rdfs:comment "Per Unit - a positive or negative value referred to a defined base. Values typically range from -10 to +10."; rdfs:label "PU"@en; "CIMDatatype" . a rdfs:Class; ; rdfs:comment "Participation factor for a given point in time."; rdfs:label "ParticipationFactorTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Kind of time period with similar intensity."; rdfs:label "PeakKind"@en; , "NC" . a rdfs:Class; ; rdfs:comment """An abstract directed dependency between two peer instances of the same domain class that defines temporal and operational constraints governing their relative execution or operation. Note: Temporal lag constraints relate the next applicable transition of the dependent to the latest applicable transition of the dependee. A dependee transition remains applicable while the dependee remains in the state resulting from that transition. If the dependee subsequently changes state before the corresponding transition of the dependent occurs, the previous transition is superseded and the constraint is evaluated from the next applicable transition. Once the corresponding transition of the dependent has occurred, the lag constraint is satisfied for that operating cycle. Each lag is qualified by its corresponding ReferenceValueKind, which specifies whether the lag represents an exact, minimum, or maximum temporal constraint."""; rdfs:label "PeerTemporalDependency"@en; "NC" . a rdfs:Class; ; rdfs:comment "Percentage on a defined base. For example, specify as 100 to indicate at the defined base."; rdfs:label "PerCent"@en; "CIMDatatype" . a rdfs:Class; ; rdfs:comment "Phase control function is a function block that calculate the operating point of the controlled equipment to achieve the target voltage."; rdfs:label "PhaseControlFunction"@en; "NC" . a rdfs:Class; ; rdfs:comment "The schedule for PhaseControlFunction."; rdfs:label "PhaseControlFunctionSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Phase control function value for a given point in time."; rdfs:label "PhaseControlFunctionTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment """A peer temporal dependency that defines temporal or operational constraints between two power bid schedules. Note: The dependency constrains activation or deactivation of the dependent power bid schedule relative to activation or deactivation of the dependee power bid schedule. Lag constraints are evaluated from the latest applicable activation or deactivation of the dependee. A subsequent state change of the dependee supersedes the previous reference transition if the corresponding transition of the dependent has not yet occurred. Example: - startToStartLag = 15M, startToStartLagKind = exact: the dependent bid is activated exactly 15 minutes after activation of the dependee bid, provided the dependee has not subsequently changed state. - finishToStartLag = 30M, finishToStartLagKind = minimum: the dependent bid may be activated no earlier than 30 minutes after deactivation of the dependee bid. - finishToFinishLag = 15M, finishToFinishLagKind = maximum: the dependent bid shall be deactivated no later than 15 minutes after deactivation of the dependee bid."""; rdfs:label "PowerBidDependency"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Power bid or offer related to a redispatch or countertrading measures. In the case of market place for economic efficiency of the bids and offers, this is equivalent to BidTimeSeries class in 62325 package."; rdfs:label "PowerBidSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Time series represent irregular values at given points in time."; rdfs:label "PowerBidScheduleTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "A generating unit or battery or aggregation that connects to the AC network using power electronics rather than rotating machines."; rdfs:label "PowerElectronicsUnit"@en . a rdfs:Class; ; rdfs:comment "Power factor control function is a function block that calculates the operating point of the controlled equipment to achieve the target power factor."; rdfs:label "PowerFactorControlFunction"@en; "NC" . a rdfs:Class; ; rdfs:comment "the schedule for PowerFactorControlFunction."; rdfs:label "PowerFactorControlFunctionSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Power factor control function value for a given point in time."; rdfs:label "PowerFactorControlFunctionTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Energy remedial action describes actions to rearrange power schedules."; rdfs:label "PowerRemedialAction"@en; "NC" . a rdfs:Class; ; rdfs:comment "The schedule for a power remedial action."; rdfs:label "PowerRemedialActionSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Regulating values at a given point in time."; rdfs:label "PowerRemedialActionTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Distribution of the bid action on the power shift keys."; rdfs:label "PowerShiftKeyDistribution"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "The schedule for Power Shift Keys."; rdfs:label "PowerShiftKeySchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Strategy of the power shift key."; rdfs:label "PowerShiftKeyStrategy"@en; "NC" . a rdfs:Class; ; rdfs:comment "A power system resource (PSR) can be an item of equipment such as a switch, an equipment container containing many individual items of equipment such as a substation, or an organisational entity such as sub-control area. Power system resources can have measurements associated."; rdfs:label "PowerSystemResource"@en; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "A power transfer corridor is defined as a set of circuits (transmission lines or transformers) separating two portions of the power system, or a subset of circuits exposed to a substantial portion of the transmission exchange between two parts of the system."; rdfs:label "PowerTransferCorridor"@en; "NC" . a rdfs:Class; ; rdfs:comment "Pressure in pascals."; rdfs:label "Pressure"@en; "CIMDatatype" . a rdfs:Class; ; rdfs:comment "Defines the rage constraint."; rdfs:label "RangeConstraint"@en; "NC"; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Product of RMS value of the voltage and the RMS value of the quadrature component of the current."; rdfs:label "ReactivePower"@en; "CIMDatatype" . a rdfs:Class; ; rdfs:comment "Reactive power control function is a function block that calculate the operating point of the controlled equipment to achieve the target reactive power."; rdfs:label "ReactivePowerControlFunction"@en; "NC" . a rdfs:Class; ; rdfs:comment "The schedule for ReactivePowerControlFunction."; rdfs:label "ReactivePowerControlFunctionSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Reactive power control function value for a given point in time."; rdfs:label "ReactivePowerControlFunctionTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Real electrical energy."; rdfs:label "RealEnergy"@en; "CIMDatatype" . a rdfs:Class; ; rdfs:comment "Kind of reference value."; rdfs:label "ReferenceValueKind"@en; , "NC" . a rdfs:Class; ; rdfs:comment "Remedial action describes one or more actions that can be performed on a given power system model situation to eliminate one or more identified breaches of constraints. The remedial action can be costly, and have a cost characteristic, or non costly. "; rdfs:label "RemedialAction"@en; "NC"; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment """Remedial action dependency is making two remedial actions depending on each other. Multiple dependency is done by multiple instances of this class. The dependency can arrive by having one of the following examples.
  • The dependent remedial action is controlled by different system operator (Modeling Authority) (e.g. SIPS that goes across control area).
  • The dependent remedial action is representing two or more remedial action that represent the same grid state alteration but with different modeling resolution (e.g. detail direct current model versus a simplified model).
  • The remedial action can be combined with other remedial action without the need to create multiple remedial action with the same grid alteration for enabling dependency.
"""; rdfs:label "RemedialActionDependency"@en; "NC" . a rdfs:Class; ; rdfs:comment "Grouping of remedial actions that can be operated together."; rdfs:label "RemedialActionGroup"@en; "NC" . ; rdfs:comment "The schedule for a remedial action group."; rdfs:label "RemedialActionGroupSchedule"@en; "NC", ; rdfs:subClassOf ; a rdfs:Class . a rdfs:Class; ; rdfs:comment "Remedial action group at a given point in time."; rdfs:label "RemedialActionGroupTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment """Remedial Action Scheme (RAS), Special Protection Schemes (SPS), System Protection Schemes (SPS) or System Integrity Protection Schemes (SIPS). A Remedial Action Scheme consists of one or more stages that can trigger and execute a protection action."""; rdfs:label "RemedialActionScheme"@en; "NC" . a rdfs:Class; ; rdfs:comment "The schedule for a remedial action scheme."; rdfs:label "RemedialActionSchemeSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Remedial action scheme at a given point in time."; rdfs:label "RemedialActionSchemeTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "A water storage facility within a hydro system, including: ponds, lakes, lagoons, and rivers. The storage is usually behind some type of dam."; rdfs:label "Reservoir"@en . a rdfs:Class; ; rdfs:comment "Reservoir schedule for elements."; rdfs:label "ReservoirSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Reservoir values for a given point in time."; rdfs:label "ReservoirTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Resistance (real part of impedance)."; rdfs:label "Resistance"@en; "CIMDatatype" . a rdfs:Class; ; rdfs:comment "A schedule resource is a market-based method for handling participation of small units, particularly located on the lower voltage level that is controlled by a Distributed System Operator (DSO). It is a collection of units that can operate in the market by providing bids, offers and a resulting committed operational schedule for the collection."; rdfs:label "ScheduleResource"@en; "NC" . a rdfs:Class; ; rdfs:comment "An area where production and/or consumption of energy can be forecasted, scheduled and measured. The area is operated by only one system operator, typically a Transmission System Operator (TSO). The area can consist of a sub area, which has the same definition as the main area, but it can be operated by another system operator (typically Distributed System Operator (DSO) or a Closed Distributed System Operator (CDSO)). This includes microgrid concept. A substation is the smallest grouping that can be included in the area. The area size should be considered in terms of the possibility of accumulated reading (settlement metering) and the capability of operating as an island."; rdfs:label "SchedulingArea"@en; "NC" . a rdfs:Class; ; rdfs:comment "A specified time period of the year."; rdfs:label "Season"@en; ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Time, in seconds."; rdfs:label "Seconds"@en; "CIMDatatype" . a rdfs:Class; ; rdfs:comment "The kind of secured exclusion reason."; rdfs:label "SecuredExclusionReasonKind"@en; , "NC" . a rdfs:Class; ; rdfs:comment "Sequence at a given point in time."; rdfs:label "SequenceTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Distance per unit of time."; rdfs:label "Speed"@en; "CIMDatatype" . a rdfs:Class; ; rdfs:comment "Stage that is triggered either by TriggerCondition or by gate condition within a stage."; rdfs:label "StageTrigger"@en; "NC" . a rdfs:Class; ; rdfs:comment "Schedule for a stage trigger."; rdfs:label "StageTriggerSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Stage trigger values at a given point in time."; rdfs:label "StageTriggerTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "A string consisting of a sequence of characters. The character encoding is UTF-8. The string length is unspecified and unlimited."; rdfs:label "String"@en; "Primitive" . a rdfs:Class; ; rdfs:comment """A string consisting of a sequence of characters. The character encoding is UTF-8. The string length is unspecified and unlimited. The primitive is serialized as literal without language support."""; rdfs:label "StringFixedLanguage"@en; "Primitive", "profcim" . a rdfs:Class; ; rdfs:comment """An IRI (Internationalized Resource Identifier) within an RDF graph is a Unicode string that conforms to the syntax defined in RFC 3987. The primitive is serialized as literal without language support. IRIs in the RDF abstract syntax must be absolute, and may contain a fragment identifier. IRI equality: Two IRIs are equal if and only if they are equivalent under Simple String Comparison according to section 5.1 of [RFC3987]. Further normalization must not be performed when comparing IRIs for equality. IRIs are a generalization of URIs [RFC3986] that permits a wider range of Unicode characters. Every absolute URI and URL is an IRI, but not every IRI is an URI. When IRIs are used in operations that are only defined for URIs, they must first be converted according to the mapping defined in section 3.1 of [RFC3987]. A notable example is retrieval over the HTTP protocol. The mapping involves UTF-8 encoding of non-ASCII characters, %-encoding of octets not allowed in URIs, and Punycode-encoding of domain names."""; rdfs:label "StringIRI"@en; "Primitive", "profcim" . a rdfs:Class; ; rdfs:comment "Value of temperature in degrees Celsius."; rdfs:label "Temperature"@en; "CIMDatatype" . a rdfs:Class; ; rdfs:comment "Time as \"hh:mm:ss.sss\", which conforms with ISO 8601. UTC time zone is specified as \"hh:mm:ss.sssZ\". A local timezone relative UTC is specified as \"hh:mm:ss.sss±hh:mm\". The second component (shown here as \"ss.sss\") could have any number of digits in its fractional part to allow any kind of precision beyond seconds."; rdfs:label "Time"@en; "Primitive" . a rdfs:Class; ; rdfs:comment "Kinds of interpolation of values between two time point. "; rdfs:label "TimeSeriesInterpolationKind"@en; , "NC" . a rdfs:Class; ; rdfs:comment "A Uniform Resource Locator (URL), colloquially termed a web address, is a reference to a web resource that specifies its location on a computer network and a mechanism for retrieving it. A URL is a specific type of Uniform Resource Identifier (URI), although many people use the two terms interchangeably.URLs occur most commonly to reference web pages (http), but are also used for file transfer (ftp), email (mailto), database access (JDBC), and many other applications."; rdfs:label "URL"@en; "Primitive", "profcim" . a rdfs:Class; ; rdfs:comment "The schedule for a unit cost."; rdfs:label "UnitCostSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Unit cost at a given point in time."; rdfs:label "UnitCostTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment """The unit multipliers defined for the CIM. When applied to unit symbols, the unit symbol is treated as a derived unit. Regardless of the contents of the unit symbol text, the unit symbol shall be treated as if it were a single-character unit symbol. Unit symbols should not contain multipliers, and it should be left to the multiplier to define the multiple for an entire data type. For example, if a unit symbol is \"m2Pers\" and the multiplier is \"k\", then the value is k(m**2/s), and the multiplier applies to the entire final value, not to any individual part of the value. This can be conceptualized by substituting a derived unit symbol for the unit type. If one imagines that the symbol \"Þ\" represents the derived unit \"m2Pers\", then applying the multiplier \"k\" can be conceptualized simply as \"kÞ\". For example, the SI unit for mass is \"kg\" and not \"g\". If the unit symbol is defined as \"kg\", then the multiplier is applied to \"kg\" as a whole and does not replace the \"k\" in front of the \"g\". In this case, the multiplier of \"m\" would be used with the unit symbol of \"kg\" to represent one gram. As a text string, this violates the instructions in IEC 80000-1. However, because the unit symbol in CIM is treated as a derived unit instead of as an SI unit, it makes more sense to conceptualize the \"kg\" as if it were replaced by one of the proposed replacements for the SI mass symbol. If one imagines that the \"kg\" were replaced by a symbol \"Þ\", then it is easier to conceptualize the multiplier \"m\" as creating the proper unit \"mÞ\", and not the forbidden unit \"mkg\"."""; rdfs:label "UnitMultiplier"@en; . a rdfs:Class; ; rdfs:comment """The derived units defined for usage in the CIM. In some cases, the derived unit is equal to an SI unit. Whenever possible, the standard derived symbol is used instead of the formula for the derived unit. For example, the unit symbol Farad is defined as \"F\" instead of \"CPerV\". In cases where a standard symbol does not exist for a derived unit, the formula for the unit is used as the unit symbol. For example, density does not have a standard symbol and so it is represented as \"kgPerm3\". With the exception of the \"kg\", which is an SI unit, the unit symbols do not contain multipliers and therefore represent the base derived unit to which a multiplier can be applied as a whole. Every unit symbol is treated as an unparseable text as if it were a single-letter symbol. The meaning of each unit symbol is defined by the accompanying descriptive text and not by the text contents of the unit symbol. To allow the widest possible range of serializations without requiring special character handling, several substitutions are made which deviate from the format described in IEC 80000-1. The division symbol \"/\" is replaced by the letters \"Per\". Exponents are written in plain text after the unit as \"m3\" instead of being formatted as \"m\" with a superscript of 3 or introducing a symbol as in \"m^3\". The degree symbol \"°\" is replaced with the letters \"deg\". Any clarification of the meaning for a substitution is included in the description for the unit symbol. Non-SI units are included in list of unit symbols to allow sources of data to be correctly labelled with their non-SI units (for example, a GPS sensor that is reporting numbers that represent feet instead of meters). This allows software to use the unit symbol information correctly convert and scale the raw data of those sources into SI-based units. The integer values are used for harmonization with IEC 61850."""; rdfs:label "UnitSymbol"@en; . a rdfs:Class; ; rdfs:comment "The kind of the value offset."; rdfs:label "ValueOffsetKind"@en; , "NC" . a rdfs:Class; ; rdfs:comment "Electrical voltage, can be both AC and DC."; rdfs:label "Voltage"@en; "CIMDatatype" . a rdfs:Class; ; rdfs:comment "Voltage angle control function is a function block that calculates operating point of the controlled equipment to achieve the target voltage angle."; rdfs:label "VoltageAngleControlFunction"@en; "NC" . a rdfs:Class; ; rdfs:comment "The schedule for VoltageAngleControlFunction."; rdfs:label "VoltageAngleControlFunctionSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Voltage angle control function value for a given point in time."; rdfs:label "VoltageAngleControlFunctionTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Voltage angle limit between two terminals. The association end OperationalLimitSet.Terminal defines one end and the host of the limit. The association end VoltageAngleLimit.AngleReferenceTerminal defines the reference terminal."; rdfs:label "VoltageAngleLimit"@en; "NC" . a rdfs:Class; ; rdfs:comment "The schedule for a voltage angle."; rdfs:label "VoltageAngleSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Voltage angle at a given point in time."; rdfs:label "VoltageAngleTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Voltage control function is a function block that calculate the operating point of the controlled equipment to achieve the target voltage."; rdfs:label "VoltageControlFunction"@en; "NC" . a rdfs:Class; ; rdfs:comment "The schedule for VoltageControlFunction."; rdfs:label "VoltageControlFunctionSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Voltage control function value for a given point in time."; rdfs:label "VoltageControlFunctionTimePoint"@en; "NC", . a rdfs:Class; ; rdfs:comment "Voltage injection control function is a function block that calculates the operating point of the controlled equipment to achieve the target voltage injection. "; rdfs:label "VoltageInjectionControlFunction"@en; "NC" . a rdfs:Class; ; rdfs:comment "The schedule for VoltageInjectionControlFunction."; rdfs:label "VoltageInjectionControlFunctionSchedule"@en; "NC", ; rdfs:subClassOf . a rdfs:Class; ; rdfs:comment "Voltage injection control function value for a given point in time."; rdfs:label "VoltageInjectionControlFunctionTimePoint"@en; "NC", . a ; rdfs:comment "This package contains datatypes used only in the RDFS header."; rdfs:label "DocStateInstructionScheduleProfile"@en . a ; rdfs:comment "This package contains the state instruction schedule profile."; rdfs:label "StateInstructionScheduleProfile"@en . a ; rdfs:comment "United Arab Emirates dirham."; rdfs:label "AED"@en; "enum" . a ; rdfs:comment "Afghan afghani."; rdfs:label "AFN"@en; "enum" . a ; rdfs:comment "Albanian lek."; rdfs:label "ALL"@en; "enum" . a ; rdfs:comment "Armenian dram."; rdfs:label "AMD"@en; "enum" . a ; rdfs:comment "Netherlands Antillean guilder."; rdfs:label "ANG"@en; "enum" . a ; rdfs:comment "Angolan kwanza."; rdfs:label "AOA"@en; "enum" . a ; rdfs:comment "Argentine peso."; rdfs:label "ARS"@en; "enum" . a ; rdfs:comment "Australian dollar."; rdfs:label "AUD"@en; "enum" . a ; rdfs:comment "Aruban florin."; rdfs:label "AWG"@en; "enum" . a ; rdfs:comment "Azerbaijani manat."; rdfs:label "AZN"@en; "enum" . a ; rdfs:comment "Bosnia and Herzegovina convertible mark."; rdfs:label "BAM"@en; "enum" . a ; rdfs:comment "Barbados dollar."; rdfs:label "BBD"@en; "enum" . a ; rdfs:comment "Bangladeshi taka."; rdfs:label "BDT"@en; "enum" . a ; rdfs:comment "Bulgarian lev."; rdfs:label "BGN"@en; "enum" . a ; rdfs:comment "Bahraini dinar."; rdfs:label "BHD"@en; "enum" . a ; rdfs:comment "Burundian franc."; rdfs:label "BIF"@en; "enum" . a ; rdfs:comment "Bermudian dollar (customarily known as Bermuda dollar)."; rdfs:label "BMD"@en; "enum" . a ; rdfs:comment "Brunei dollar."; rdfs:label "BND"@en; "enum" . a ; rdfs:comment "Boliviano."; rdfs:label "BOB"@en; "enum" . a ; rdfs:comment "Bolivian Mvdol (funds code)."; rdfs:label "BOV"@en; "enum" . a ; rdfs:comment "Brazilian real."; rdfs:label "BRL"@en; "enum" . a ; rdfs:comment "Bahamian dollar."; rdfs:label "BSD"@en; "enum" . a ; rdfs:comment "Bhutanese ngultrum."; rdfs:label "BTN"@en; "enum" . a ; rdfs:comment "Botswana pula."; rdfs:label "BWP"@en; "enum" . a ; rdfs:comment "Belarusian ruble."; rdfs:label "BYR"@en; "enum" . a ; rdfs:comment "Belize dollar."; rdfs:label "BZD"@en; "enum" . a ; rdfs:comment "Canadian dollar."; rdfs:label "CAD"@en; "enum" . a ; rdfs:comment "Congolese franc."; rdfs:label "CDF"@en; "enum" . a ; rdfs:comment "Swiss franc."; rdfs:label "CHF"@en; "enum" . a ; rdfs:comment "Unidad de Fomento (funds code), Chile."; rdfs:label "CLF"@en; "enum" . a ; rdfs:comment "Chilean peso."; rdfs:label "CLP"@en; "enum" . a ; rdfs:comment "Chinese yuan."; rdfs:label "CNY"@en; "enum" . a ; rdfs:comment "Colombian peso."; rdfs:label "COP"@en; "enum" . a ; rdfs:comment "Unidad de Valor Real."; rdfs:label "COU"@en; "enum" . a ; rdfs:comment "Costa Rican colon."; rdfs:label "CRC"@en; "enum" . a ; rdfs:comment "Cuban convertible peso."; rdfs:label "CUC"@en; "enum" . a ; rdfs:comment "Cuban peso."; rdfs:label "CUP"@en; "enum" . a ; rdfs:comment "Cape Verde escudo."; rdfs:label "CVE"@en; "enum" . a ; rdfs:comment "Czech koruna."; rdfs:label "CZK"@en; "enum" . a ; rdfs:comment "Djiboutian franc."; rdfs:label "DJF"@en; "enum" . a ; rdfs:comment "Danish krone."; rdfs:label "DKK"@en; "enum" . a ; rdfs:comment "Dominican peso."; rdfs:label "DOP"@en; "enum" . a ; rdfs:comment "Algerian dinar."; rdfs:label "DZD"@en; "enum" . a ; rdfs:comment "Estonian kroon."; rdfs:label "EEK"@en; "enum" . a ; rdfs:comment "Egyptian pound."; rdfs:label "EGP"@en; "enum" . a ; rdfs:comment "Eritrean nakfa."; rdfs:label "ERN"@en; "enum" . a ; rdfs:comment "Ethiopian birr."; rdfs:label "ETB"@en; "enum" . a ; rdfs:comment "Euro."; rdfs:label "EUR"@en; "enum" . a ; rdfs:comment "Fiji dollar."; rdfs:label "FJD"@en; "enum" . a ; rdfs:comment "Falkland Islands pound."; rdfs:label "FKP"@en; "enum" . a ; rdfs:comment "Pound sterling."; rdfs:label "GBP"@en; "enum" . a ; rdfs:comment "Georgian lari."; rdfs:label "GEL"@en; "enum" . a ; rdfs:comment "Ghanaian cedi."; rdfs:label "GHS"@en; "enum" . a ; rdfs:comment "Gibraltar pound."; rdfs:label "GIP"@en; "enum" . a ; rdfs:comment "Gambian dalasi."; rdfs:label "GMD"@en; "enum" . a ; rdfs:comment "Guinean franc."; rdfs:label "GNF"@en; "enum" . a ; rdfs:comment "Guatemalan quetzal."; rdfs:label "GTQ"@en; "enum" . a ; rdfs:comment "Guyanese dollar."; rdfs:label "GYD"@en; "enum" . a ; rdfs:comment "Hong Kong dollar."; rdfs:label "HKD"@en; "enum" . a ; rdfs:comment "Honduran lempira."; rdfs:label "HNL"@en; "enum" . a ; rdfs:comment "Croatian kuna."; rdfs:label "HRK"@en; "enum" . a ; rdfs:comment "Haitian gourde."; rdfs:label "HTG"@en; "enum" . a ; rdfs:comment "Hungarian forint."; rdfs:label "HUF"@en; "enum" . a ; rdfs:comment "Indonesian rupiah."; rdfs:label "IDR"@en; "enum" . a ; rdfs:comment "Israeli new sheqel."; rdfs:label "ILS"@en; "enum" . a ; rdfs:comment "Indian rupee."; rdfs:label "INR"@en; "enum" . a ; rdfs:comment "Iraqi dinar."; rdfs:label "IQD"@en; "enum" . a ; rdfs:comment "Iranian rial."; rdfs:label "IRR"@en; "enum" . a ; rdfs:comment "Icelandic króna."; rdfs:label "ISK"@en; "enum" . a ; rdfs:comment "Jamaican dollar."; rdfs:label "JMD"@en; "enum" . a ; rdfs:comment "Jordanian dinar."; rdfs:label "JOD"@en; "enum" . a ; rdfs:comment "Japanese yen."; rdfs:label "JPY"@en; "enum" . a ; rdfs:comment "Kenyan shilling."; rdfs:label "KES"@en; "enum" . a ; rdfs:comment "Kyrgyzstani som."; rdfs:label "KGS"@en; "enum" . a ; rdfs:comment "Cambodian riel."; rdfs:label "KHR"@en; "enum" . a ; rdfs:comment "Comoro franc."; rdfs:label "KMF"@en; "enum" . a ; rdfs:comment "North Korean won."; rdfs:label "KPW"@en; "enum" . a ; rdfs:comment "South Korean won."; rdfs:label "KRW"@en; "enum" . a ; rdfs:comment "Kuwaiti dinar."; rdfs:label "KWD"@en; "enum" . a ; rdfs:comment "Cayman Islands dollar."; rdfs:label "KYD"@en; "enum" . a ; rdfs:comment "Kazakhstani tenge."; rdfs:label "KZT"@en; "enum" . a ; rdfs:comment "Lao kip."; rdfs:label "LAK"@en; "enum" . a ; rdfs:comment "Lebanese pound."; rdfs:label "LBP"@en; "enum" . a ; rdfs:comment "Sri Lanka rupee."; rdfs:label "LKR"@en; "enum" . a ; rdfs:comment "Liberian dollar."; rdfs:label "LRD"@en; "enum" . a ; rdfs:comment "Lesotho loti."; rdfs:label "LSL"@en; "enum" . a ; rdfs:comment "Lithuanian litas."; rdfs:label "LTL"@en; "enum" . a ; rdfs:comment "Latvian lats."; rdfs:label "LVL"@en; "enum" . a ; rdfs:comment "Libyan dinar."; rdfs:label "LYD"@en; "enum" . a ; rdfs:comment "Moroccan dirham."; rdfs:label "MAD"@en; "enum" . a ; rdfs:comment "Moldovan leu."; rdfs:label "MDL"@en; "enum" . a ; rdfs:comment "Malagasy ariary."; rdfs:label "MGA"@en; "enum" . a ; rdfs:comment "Macedonian denar."; rdfs:label "MKD"@en; "enum" . a ; rdfs:comment "Myanma kyat."; rdfs:label "MMK"@en; "enum" . a ; rdfs:comment "Mongolian tugrik."; rdfs:label "MNT"@en; "enum" . a ; rdfs:comment "Macanese pataca."; rdfs:label "MOP"@en; "enum" . a ; rdfs:comment "Mauritanian ouguiya."; rdfs:label "MRO"@en; "enum" . a ; rdfs:comment "Mauritian rupee."; rdfs:label "MUR"@en; "enum" . a ; rdfs:comment "Maldivian rufiyaa."; rdfs:label "MVR"@en; "enum" . a ; rdfs:comment "Malawian kwacha."; rdfs:label "MWK"@en; "enum" . a ; rdfs:comment "Mexican peso."; rdfs:label "MXN"@en; "enum" . a ; rdfs:comment "Malaysian ringgit."; rdfs:label "MYR"@en; "enum" . a ; rdfs:comment "Mozambican metical."; rdfs:label "MZN"@en; "enum" . a ; rdfs:comment "Namibian dollar."; rdfs:label "NAD"@en; "enum" . a ; rdfs:comment "Nigerian naira."; rdfs:label "NGN"@en; "enum" . a ; rdfs:comment "Cordoba oro."; rdfs:label "NIO"@en; "enum" . a ; rdfs:comment "Norwegian krone."; rdfs:label "NOK"@en; "enum" . a ; rdfs:comment "Nepalese rupee."; rdfs:label "NPR"@en; "enum" . a ; rdfs:comment "New Zealand dollar."; rdfs:label "NZD"@en; "enum" . a ; rdfs:comment "Omani rial."; rdfs:label "OMR"@en; "enum" . a ; rdfs:comment "Panamanian balboa."; rdfs:label "PAB"@en; "enum" . a ; rdfs:comment "Peruvian nuevo sol."; rdfs:label "PEN"@en; "enum" . a ; rdfs:comment "Papua New Guinean kina."; rdfs:label "PGK"@en; "enum" . a ; rdfs:comment "Philippine peso."; rdfs:label "PHP"@en; "enum" . a ; rdfs:comment "Pakistani rupee."; rdfs:label "PKR"@en; "enum" . a ; rdfs:comment "Polish zloty."; rdfs:label "PLN"@en; "enum" . a ; rdfs:comment "Paraguayan guaraní."; rdfs:label "PYG"@en; "enum" . a ; rdfs:comment "Qatari rial."; rdfs:label "QAR"@en; "enum" . a ; rdfs:comment "Romanian new leu."; rdfs:label "RON"@en; "enum" . a ; rdfs:comment "Serbian dinar."; rdfs:label "RSD"@en; "enum" . a ; rdfs:comment "Russian rouble."; rdfs:label "RUB"@en; "enum" . a ; rdfs:comment "Rwandan franc."; rdfs:label "RWF"@en; "enum" . a ; rdfs:comment "Saudi riyal."; rdfs:label "SAR"@en; "enum" . a ; rdfs:comment "Solomon Islands dollar."; rdfs:label "SBD"@en; "enum" . a ; rdfs:comment "Seychelles rupee."; rdfs:label "SCR"@en; "enum" . a ; rdfs:comment "Sudanese pound."; rdfs:label "SDG"@en; "enum" . a ; rdfs:comment "Swedish krona/kronor."; rdfs:label "SEK"@en; "enum" . a ; rdfs:comment "Singapore dollar."; rdfs:label "SGD"@en; "enum" . a ; rdfs:comment "Saint Helena pound."; rdfs:label "SHP"@en; "enum" . a ; rdfs:comment "Sierra Leonean leone."; rdfs:label "SLL"@en; "enum" . a ; rdfs:comment "Somali shilling."; rdfs:label "SOS"@en; "enum" . a ; rdfs:comment "Surinamese dollar."; rdfs:label "SRD"@en; "enum" . a ; rdfs:comment "São Tomé and Príncipe dobra."; rdfs:label "STD"@en; "enum" . a ; rdfs:comment "Syrian pound."; rdfs:label "SYP"@en; "enum" . a ; rdfs:comment "Lilangeni."; rdfs:label "SZL"@en; "enum" . a ; rdfs:comment "Thai baht."; rdfs:label "THB"@en; "enum" . a ; rdfs:comment "Tajikistani somoni."; rdfs:label "TJS"@en; "enum" . a ; rdfs:comment "Turkmenistani manat."; rdfs:label "TMT"@en; "enum" . a ; rdfs:comment "Tunisian dinar."; rdfs:label "TND"@en; "enum" . a ; rdfs:comment "Tongan pa'anga."; rdfs:label "TOP"@en; "enum" . a ; rdfs:comment "Turkish lira."; rdfs:label "TRY"@en; "enum" . a ; rdfs:comment "Trinidad and Tobago dollar."; rdfs:label "TTD"@en; "enum" . a ; rdfs:comment "New Taiwan dollar."; rdfs:label "TWD"@en; "enum" . a ; rdfs:comment "Tanzanian shilling."; rdfs:label "TZS"@en; "enum" . a ; rdfs:comment "Ukrainian hryvnia."; rdfs:label "UAH"@en; "enum" . a ; rdfs:comment "Ugandan shilling."; rdfs:label "UGX"@en; "enum" . a ; rdfs:comment "United States dollar."; rdfs:label "USD"@en; "enum" . a ; rdfs:comment "Uruguayan peso."; rdfs:label "UYU"@en; "enum" . a ; rdfs:comment "Uzbekistan som."; rdfs:label "UZS"@en; "enum" . a ; rdfs:comment "Venezuelan bolívar fuerte."; rdfs:label "VEF"@en; "enum" . a ; rdfs:comment "Vietnamese Dong."; rdfs:label "VND"@en; "enum" . a ; rdfs:comment "Vanuatu vatu."; rdfs:label "VUV"@en; "enum" . a ; rdfs:comment "Samoan tala."; rdfs:label "WST"@en; "enum" . a ; rdfs:comment "CFA franc BEAC."; rdfs:label "XAF"@en; "enum" . a ; rdfs:comment "East Caribbean dollar."; rdfs:label "XCD"@en; "enum" . a ; rdfs:comment "CFA Franc BCEAO."; rdfs:label "XOF"@en; "enum" . a ; rdfs:comment "CFP franc."; rdfs:label "XPF"@en; "enum" . a ; rdfs:comment "Yemeni rial."; rdfs:label "YER"@en; "enum" . a ; rdfs:comment "South African rand."; rdfs:label "ZAR"@en; "enum" . a ; rdfs:comment "Zambian kwacha."; rdfs:label "ZMK"@en; "enum" . a ; rdfs:comment "Zimbabwe dollar."; rdfs:label "ZWL"@en; "enum" . a ; rdfs:comment "All days of the week."; rdfs:label "all"@en; "enum" . a ; rdfs:comment "A day that is a gap between two distinguished days e.g holiday and weekend that leads to an abnormal scheduling behavior. e.g. if Ascension day falls on a Thursday, then Friday would be a bridge day due to the schedule will not have a normal Friday consumption and production."; rdfs:label "bridgeDay"@en; "enum" . a ; rdfs:comment "Friday as the day of the week."; rdfs:label "friday"@en; "enum" . a ; rdfs:comment "Monday as the day of the week."; rdfs:label "monday"@en; "enum" . a ; rdfs:comment "Public holiday is an officially designated day when most workplaces and schools are closed."; rdfs:label "publicHoliday"@en; "enum" . a ; rdfs:comment "Saturday as the day of the week."; rdfs:label "saturday"@en; "enum" . a ; rdfs:comment "Sunday as the day of the week."; rdfs:label "sunday"@en; "enum" . a ; rdfs:comment "Thursday as the day of the week."; rdfs:label "thursday"@en; "enum" . a ; rdfs:comment "Tuesday as the day of the week."; rdfs:label "tuesday"@en; "enum" . a ; rdfs:comment "Wednesday as the day of the week."; rdfs:label "wednesday"@en; "enum" . a ; rdfs:comment "Day of the week other than Sunday or Saturday."; rdfs:label "weekday"@en; "enum" . a ; rdfs:comment "Day of the week which is Sunday or Saturday."; rdfs:label "weekend"@en; "enum" . a ; rdfs:comment "The dependee and dependent shall not both be active or effective at the same time."; rdfs:label "exclusive"@en; "enum" . a ; rdfs:comment "The dependent shall only be active or effective while the dependee is active or effective."; rdfs:label "inclusive"@en; "enum" . a ; rdfs:comment """The dependee constrains the dependent without requiring the dependent to become active or effective. Note: A restrictive dependency defines temporal or operational constraints on the behaviour of the dependent while leaving its activation or operation optional."""; rdfs:label "restrictive"@en; "enum" . a ; rdfs:comment "Scenario focus on consumption of energy."; rdfs:label "consumption"@en; "enum" . a ; rdfs:comment "Scenario focus on export of energy."; rdfs:label "export"@en; "enum" . a ; rdfs:comment "Scenario focus on import of energy."; rdfs:label "import"@en; "enum" . a ; rdfs:comment "Scenario focus on production of energy."; rdfs:label "production"@en; "enum" . a ; rdfs:comment "Scenario focus on storage of energy."; rdfs:label "storage"@en; "enum" . a ; rdfs:comment "Regulation activation that decreases the system’s net power injection — achieved either by decreasing generation or increasing consumption. Used for down-regulation bids or activations."; rdfs:label "down"@en; "enum" . a ; rdfs:comment "No activation or neutral position; used for capacity or reserve states that maintain stability without a directional effect (e.g., system in balanced or standby mode)."; rdfs:label "stable"@en; "enum" . a ; rdfs:comment "Regulation activation that increases the system’s net power injection — achieved either by increasing generation or decreasing consumption. Used for up-regulation bids or activations."; rdfs:label "up"@en; "enum" . a ; rdfs:comment "Product or capacity symmetrical for both up- and down-regulation; the same magnitude applies in both directions. Common for bidirectional balancing services (e.g., symmetrical aFRR capacity)."; rdfs:label "upAndDown"@en; "enum" . a ; rdfs:comment "Off-peak refer to periods of lower demand for a particular service or commodity."; rdfs:label "offPeak"@en; "enum" . rdfs:comment "Off-peak refer to periods of higher demand for a particular service or commodity."; rdfs:label "onPeak"@en; a ; "enum" . a rdf:Property; "No"; rdfs:comment "The schedule of the control function."; rdfs:domain ; ; rdfs:label "ACEmulationControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The control function that has this schedule."; rdfs:domain ; ; rdfs:label "ACEmulationControlFunction"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point of the schedule."; rdfs:domain ; ; rdfs:label "ACEmulationControlFunctionTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The schedule that has this time point."; rdfs:domain ; ; rdfs:label "ACEmulationControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Control system gain in AC transmission emulation control measured in MW/deg. It plays the role of an admittance of the equivalent AC transmission line that the control is emulating the higher is the gain the higher is the active power transfer at steady state."; ; rdfs:domain ; rdfs:label "gain"@en; ; , "NC" . a rdf:Property; rdfs:comment "Existing active power setpoint used to calculate the active power setpoint of the AC emulation control."; ; rdfs:domain ; rdfs:label "referenceP"@en; ; , "NC" . a rdf:Property; rdfs:comment """Control system time constant in AC transmission emulation control. It affects the time needed to reach a new steady state equilibrium point after a network perturbation extremely important to guarantee N-1 relief related to an interconnection. The higher is time constant the slower is the DC system dynamic."""; ; rdfs:domain ; rdfs:label "timeConstant"@en; ; , "NC" . a rdf:Property; rdfs:domain ; "M"; rdfs:label "multiplier"@en; ; rdfs:range ; . a rdf:Property; rdfs:domain ; "W"; rdfs:label "unit"@en; ; rdfs:range ; . a rdf:Property; ; rdfs:domain ; rdfs:label "value"@en; ; . a rdf:Property; "No"; rdfs:comment "The schedule of the control function."; rdfs:domain ; ; rdfs:label "ActivePowerControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The control function that has this schedule."; rdfs:domain ; ; rdfs:label "ActivePowerControlFunction"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point of the schedule."; rdfs:domain ; ; rdfs:label "ActivePowerControlFunctionTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The schedule that has this time point."; rdfs:domain ; ; rdfs:label "ActivePowerControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Target value for the active power that the control function is calculating to achieve by adjusting the operational setting to the controlled equipment."; ; rdfs:domain ; rdfs:label "targetValue"@en; ; , "NC" . a rdf:Property; rdfs:domain ; "none"; rdfs:label "multiplier"@en; ; rdfs:range ; . a rdf:Property; rdfs:domain ; "deg"; rdfs:label "unit"@en; ; rdfs:range ; . a rdf:Property; ; rdfs:domain ; rdfs:label "value"@en; ; . a rdf:Property; "No"; rdfs:comment "The schedule for this resource."; rdfs:domain ; ; rdfs:label "AreaReserveResourceRegularSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The schedule for this resource."; rdfs:domain ; ; rdfs:label "AreaReserveResourceSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The resource that has a schedule."; rdfs:domain ; ; rdfs:label "AreaReserveResource"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The resource that has a schedule."; rdfs:domain ; ; rdfs:label "AreaReserveResource"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point for this schedule."; rdfs:domain ; ; rdfs:label "AreaReserveResourceTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The schedule that has a time point. "; rdfs:domain ; ; rdfs:label "AreaReserveResourceSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "Amount of active power currently activated for the reserve product."; ; rdfs:domain ; rdfs:label "activatedP"@en; ; , "NC" . a rdf:Property; rdfs:comment "Amount of active power capability allocated from the associated resource to the area for the given reserve product."; ; rdfs:domain ; rdfs:label "allocatedP"@en; ; , "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Amount of active power currently available for provision of the reserve product."; ; rdfs:domain ; rdfs:label "availableP"@en; ; , "NC" . a rdf:Property; rdfs:comment "Amount of active power contracted for the reserve product."; ; rdfs:domain ; rdfs:label "contractedP"@en; ; , "NC" . a rdf:Property; rdfs:comment "Identifies if the unit is enabled to accept a dispatch instruction. If true, the unit is enabled to accept a dispatch instruction. If false, the unit has the capability, but it is not enabled to receive a dispatch instruction."; ; rdfs:domain ; rdfs:label "enabled"@en; ; , "NC" . a rdf:Property; rdfs:comment "Type of reserve product represented by the allocation."; rdfs:domain ; rdfs:label "kind"@en; ; rdfs:range ; , "NC" . a rdf:Property; rdfs:comment "Relative priority for activation or selection within an area or aggregated reserve structure."; ; rdfs:domain ; rdfs:label "priority"@en; ; , "NC" . a rdf:Property; rdfs:comment "Direction of the product flow."; rdfs:domain ; rdfs:label "regulationDirection"@en; ; rdfs:range ; , "NC" . a rdf:Property; "No"; rdfs:comment "Regular schedule that belongs to an assessed element."; rdfs:domain ; ; rdfs:label "AssessedElementRegularSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "Assessed element schedule for an assessed element."; rdfs:domain ; ; rdfs:label "AssessedElementSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Assessed Element that has regular schedules."; rdfs:domain ; ; rdfs:label "AssessedElement"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "Assessed element regular time point which belong to an assessed element regular schedule."; rdfs:domain ; ; rdfs:label "AssessedElementRegularTimePoint"@en; ; rdfs:range ; "NC", . a rdf:Property; "Yes"; rdfs:comment "Assessed element regular schedule which has assessed element regular time points."; rdfs:domain ; ; rdfs:label "AssessedElementRegularSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment """The percentage (appointed to a region) of the remaining margin obtained in the grid model to reach its current limit. The maximum percentage shall by default be 10% of the remaining margin. It is only used when an assessed element is considered conservative for a region. The allowed value range is [0,100]."""; ; rdfs:domain ; rdfs:label "appointedMargin"@en; ; , "NC" . a rdf:Property; rdfs:comment "It identifies if the assessed element is enabled. True means enabled, False means disabled."; ; rdfs:domain ; rdfs:label "enabled"@en; ; , "NC" . a rdf:Property; rdfs:comment "Maximum flow on an a conducting equipment or a collection of conducting equipment forming a power transfer corridor. For assessed elements that is becomes critical due to contingency, this value represents the maximum flow with remedial action taken into consideration."; ; rdfs:domain ; rdfs:label "maxFlow"@en; ; , "NC" . a rdf:Property; rdfs:comment """A margin defined only for scanned AssessedElement (If AssessedElement.ScannedForRegion is present) in order to represent the influence of available remedial action which is not cross-border relevant remedial action. The margin is modifying the limits used for the assessment whatever the limit it is (e.g. PATL, TATL).This symbolizes a remedial action that can be applied internally by the System Operator. It will be resolved by the System Operator and not by the optimization of remedial actions. The attribute shall be a positive value. The allowed value range is [0,100]."""; ; rdfs:domain ; rdfs:label "positiveVirtualMargin"@en; ; , "NC" . a rdf:Property; rdfs:comment """Threshold percentage that a scanned element can be overloaded, on a given element, on top of any overload prior to optimisation (default= 5%). e.g. Initial loading of the element is 110%, with a 5% scanned threshold margin, the new maximum is 115% of the limit (e.g. PATL, TATL, etc). The allowed value range is [0,100]."""; ; rdfs:domain ; rdfs:label "scannedThresholdMargin"@en; ; , "NC" . a rdf:Property; "Yes"; rdfs:comment "Assessed element which has an assessed element schedule."; rdfs:domain ; ; rdfs:label "AssessedElement"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point that relates to this assessed element schedule."; rdfs:domain ; ; rdfs:label "AssessedElementTimePoint"@en; ; rdfs:range ; , "NC" . a rdf:Property; "Yes"; rdfs:comment "The assessed element schedule that has this time point."; rdfs:domain ; ; rdfs:label "AssessedElementSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment """The percentage (appointed to a region) of the remaining margin obtained in the grid model to reach its current limit. The maximum percentage shall by default be 10% of the remaining margin. It is only used when an assessed element is considered conservative for a region. The allowed value range is [0,100]."""; ; rdfs:domain ; rdfs:label "appointedMargin"@en; ; , "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "A positive value expressed in MW, calculated and provided by the coordinated capacity calculator (CCC) for the reduction of Remaining Available Margin (RAM) in order to ensure grid security."; ; rdfs:domain ; rdfs:label "coordinatedValidationAdjustment"@en; ; , "NC" . a rdf:Property; rdfs:comment "A text description provided by the coordinated capacity calculator (CCC) for justifying the reduction of Remaining Available Margin (RAM) by means of Coordinated Validation Adjustment (CVA). This justification is not intended for any application processing purpose, it should only be used for reporting."; ; rdfs:domain ; rdfs:label "coordinatedValidationAdjustmentJustification"@en; ; , "NC" . a rdf:Property; rdfs:comment "Justification indicating the kind of critical element contingency. This justification is not intended for any application processing purpose, it should only be used for reporting."; ; rdfs:domain ; rdfs:label "criticalElementJustification"@en; ; , "NC", "deprecated" . a rdf:Property; rdfs:comment "It identifies if the assessed element is enabled. True means enabled, False means disabled."; ; rdfs:domain ; rdfs:label "enabled"@en; ; , "NC" . a rdf:Property; rdfs:comment "Reason for not associating this assessed element with a secured region."; rdfs:domain ; rdfs:label "exclusionReason"@en; ; rdfs:range ; , "NC" . a rdf:Property; rdfs:comment "A positive value expressed in MW, calculated and provided by System Operators from their individual validation process for the reduction of Remaining Available Margin in order to ensure grid security."; ; rdfs:domain ; rdfs:label "individualValidationAdjustment"@en; ; , "NC" . a rdf:Property; rdfs:comment "A text description provided by System Operators for justifying the reduction of Remaining Available Margin (RAM) by means of Individual Validation Adjustment (IVA). This justification is not intended for any application processing purpose, it should only be used for reporting."; ; rdfs:domain ; rdfs:label "individualValidationAdjustmentJustification"@en; ; , "NC" . a rdf:Property; rdfs:comment "A positive value expressed in MW, calculated by the coordinated capacity calculator (CCC) based on the provided Individual Validation Adjustment (IVA) by System Operators in order to show the actual reduction of Remaining Available Margin (RAM). Individual Validation Adjustment Share is a positive non-zero value. It is equal or less than the Individual Validation Adjustment value. "; ; rdfs:domain ; rdfs:label "individualValidationAdjustmentShare"@en; ; , "NC" . a rdf:Property; rdfs:comment "Maximum flow on an a conducting equipment or a collection of conducting equipment forming a power transfer corridor. For assessed elements that is becomes critical due to contingency, this value represents the maximum flow with remedial action taken into consideration."; ; rdfs:domain ; rdfs:label "maxFlow"@en; ; , "NC" . a rdf:Property; rdfs:comment """A margin defined only for scanned AssessedElement (If AssessedElement.ScannedForRegion is present) in order to represent the influence of available remedial action which is not cross-border relevant remedial action. The margin is modifying the limits used for the assessment whatever the limit it is (e.g. PATL, TATL).This symbolizes a remedial action that can be applied internally by the System Operator. It will be resolved by the System Operator and not by the optimization of remedial actions. The attribute shall be a positive value. The allowed value range is [0,100]."""; ; rdfs:domain ; rdfs:label "positiveVirtualMargin"@en; ; , "NC" . a rdf:Property; rdfs:comment """Threshold percentage that a scanned element can be overloaded, on a given element, on top of any overload prior to optimisation (default= 5%). e.g. Initial loading of the element is 110%, with a 5% scanned threshold margin, the new maximum is 115% of the limit (e.g. PATL, TATL, etc). The allowed value range is [0,100]."""; ; rdfs:domain ; rdfs:label "scannedThresholdMargin"@en; ; , "NC" . a rdf:Property; rdfs:comment "Justification indicating the target remaining available margin. This justification is not intended for any application processing purpose, it should only be used for reporting."; ; rdfs:domain ; rdfs:label "targetRemainingAvailableMarginJustification"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "Enabling schedule which belongs to the assessed element with contingency."; rdfs:domain ; ; rdfs:label "GenericEnablingSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "Enabling schedule which belongs to the assessed element with remedial action."; rdfs:domain ; ; rdfs:label "GenericEnablingSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "Enabling schedule associated to an automation function."; rdfs:domain ; ; rdfs:label "GenericEnablingSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The availability schedule which belongs to the availability timepoint."; rdfs:domain ; ; rdfs:label "GenericAvailabilitySchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "It identifies if the element is available. True means available, False means unavailable."; ; rdfs:domain ; rdfs:label "available"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "Base case current limit schedule associated with a base case current limit."; rdfs:domain ; ; rdfs:label "BaseCaseCurrentLimitSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Base case current limit which has base case current limit schedule."; rdfs:domain ; ; rdfs:label "BaseCaseCurrentLimit"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "Base case current limit time point that relates to this base case current limit schedule."; rdfs:domain ; ; rdfs:label "BaseCaseCurrentLimitTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Base case current limit schedule that has time point."; rdfs:domain ; ; rdfs:label "BaseCaseCurrentLimitSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Value of current limit. The attribute shall be a positive value or zero."; ; rdfs:domain ; rdfs:label "value"@en; ; , "NC" . a rdf:Property; "Yes"; rdfs:comment "HourPattern that has base regular interval schedule."; rdfs:domain ; ; rdfs:label "HourPattern"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Season associated with a base regular interval schedule."; rdfs:domain ; ; rdfs:label "Season"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "Day of the week for which the schedule is valid for."; rdfs:domain ; rdfs:label "dayOfWeek"@en; ; rdfs:range ; , "NC" . a rdf:Property; rdfs:comment "Interval end time for which the schedule is valid for."; ; rdfs:domain ; rdfs:label "intervalEndTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Interval start time for which the schedule is valid for."; ; rdfs:domain ; rdfs:label "intervalStartTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Action method used to create the value. This is used for identification in the case where there is multiple time series for the same validity period and kind. "; ; rdfs:domain ; rdfs:label "actionMethod"@en; ; , "NC" . a rdf:Property; rdfs:comment "Kind of interpolation done between time point."; rdfs:domain ; rdfs:label "interpolationKind"@en; ; rdfs:range ; , "NC" . a rdf:Property; rdfs:comment "Kind of base time series."; rdfs:domain ; rdfs:label "timeSeriesKind"@en; ; rdfs:range ; , "NC" . a rdf:Property; "No"; rdfs:comment "The climate zone regular schedule for this climate zone."; rdfs:domain ; ; rdfs:label "ClimateZoneRegularSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The climate zone schedule for the clomate zone."; rdfs:domain ; ; rdfs:label "ClimateZoneSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The climate zone that has regular schedule."; rdfs:domain ; ; rdfs:label "ClimateZone"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment """An index representing the avalanche danger for the corresponding time interval. Note: The applicable avalanche danger methodology and classification are identified through the associated data provenance. The CIM model does not prescribe a particular avalanche danger scale. Where the index represents categorical danger levels, the numerical values shall not be assumed to form a linear scale. Example: Using the European Avalanche Danger Scale: \"1\" (Low), \"2\" (Moderate), \"3\" (Considerable), \"4\" (High), \"5\" (Very high)."""; ; rdfs:domain ; rdfs:label "avalancheDangerIndex"@en; ; , "NC" . a rdf:Property; rdfs:comment "The proportion of the sky covered by cloud for the corresponding time interval."; ; rdfs:domain ; rdfs:label "cloudCover"@en; ; , "NC" . a rdf:Property; rdfs:comment "The dew-point temperature at 2 metres above ground level for the corresponding time interval."; ; rdfs:domain ; rdfs:label "dewPointTempAt2m"@en; ; , "NC" . a rdf:Property; rdfs:comment "The diffuse solar irradiance for the corresponding time interval."; ; rdfs:domain ; rdfs:label "diffuseSolarIrradiance"@en; ; , "NC" . a rdf:Property; rdfs:comment "The direct solar irradiance for the corresponding time interval."; ; rdfs:domain ; rdfs:label "directSolarIrradiance"@en; ; , "NC" . a rdf:Property; rdfs:comment """The Drought Code for the corresponding time interval. Note: The Drought Code is a component of the Canadian Fire Weather Index System representing the moisture condition of deep, compact organic fuel layers. It is particularly useful for representing the cumulative effect of prolonged dry conditions and seasonal drought on wildfire potential. Higher values indicate drier conditions. The attribute is used when the applicable wildfire methodology provides a Drought Code. Example: Values such as \"15\", \"300\" and \"600\" represent progressively drier conditions in the Drought Code scale. No universal low, moderate or high classification is implied by these example values; interpretation is provided by the applicable methodology and provenance."""; ; rdfs:domain ; rdfs:label "droughtCode"@en; ; , "NC" . a rdf:Property; rdfs:comment """The evaporation and evapotranspiration during the corresponding time interval, expressed as an equivalent depth of water. Note: The sign convention, where relevant, is defined by the applicable data specification."""; ; rdfs:domain ; rdfs:label "evaporation"@en; ; , "NC" . a rdf:Property; rdfs:comment """A fire-weather index indicating the meteorological conditions relevant to wildfire danger for the corresponding time interval. Note: The applicable fire-weather index methodology and classification are identified through the associated data provenance. The CIM model does not prescribe a specific wildfire classification. The Canadian Fire Weather Index (FWI) System, as used by European Forest Fire Information System (EFFIS), is one example. In this system, the index combines fuel-moisture and fire-behaviour components derived from temperature, relative humidity, wind speed and precipitation. Higher values indicate conditions increasingly favourable to intense wildfire. Example: Using the EFFIS classification: \"5.0\" (Very low), \"10.0\" (Low), \"15.0\" (Moderate), \"37.77\" (High), \"40.01\" (Very high), \"55.55\" (Extreme)."""; ; rdfs:domain ; rdfs:label "fireWeatherIndex"@en; ; , "NC" . a rdf:Property; rdfs:comment "The number of days with freezing precipitation within the corresponding time interval."; ; rdfs:domain ; rdfs:label "freezingPrecipitationDays"@en; ; , "NC" . a rdf:Property; rdfs:comment "The number of frost days within the corresponding time interval."; ; rdfs:domain ; rdfs:label "frostDays"@en; ; , "NC" . a rdf:Property; rdfs:comment """The global solar irradiance for the corresponding time interval. Note: Global solar irradiance represents the total direct and diffuse solar power incident per unit area on the applicable reference surface. It may be used as an environmental input for applications such as photovoltaic production and thermal rating of overhead conductors. The orientation of the reference surface is defined by the applicable dataset or provenance information."""; ; rdfs:domain ; rdfs:label "globalSolarIrradiance"@en; ; , "NC" . a rdf:Property; rdfs:comment "The number of days on which hail occurs within the corresponding time interval."; ; rdfs:domain ; rdfs:label "hailDays"@en; ; , "NC" . a rdf:Property; rdfs:comment "The number of days occurring as part of a heatwave within the corresponding time interval."; ; rdfs:domain ; rdfs:label "heatwaveDays"@en; ; , "NC" . a rdf:Property; rdfs:comment "The number of days meeting the applicable hot-day criterion within the corresponding time interval."; ; rdfs:domain ; rdfs:label "hotDays"@en; ; , "NC" . a rdf:Property; rdfs:comment """The energy equivalent of natural hydro inflow associated with hydro resources in the ClimateZone during the corresponding time interval. Note: The value represents inflow energy for the interval. For example, a weekly TimePoint may contain the natural hydro inflow energy for that week."""; ; rdfs:domain ; rdfs:label "hydroInflow"@en; ; , "NC" . a rdf:Property; rdfs:comment "The number of days meeting the applicable icing criterion within the corresponding time interval."; ; rdfs:domain ; rdfs:label "icingDays"@en; ; , "NC" . a rdf:Property; rdfs:comment "The number of lightning events per unit area occurring during the corresponding time interval."; ; rdfs:domain ; rdfs:label "lightningDensity"@en; ; , "NC" . a rdf:Property; rdfs:comment """The maximum air temperature at 2 metres above ground level during the corresponding time interval. Note: This time series is intended for datasets providing maximum temperature directly."""; ; rdfs:domain ; rdfs:label "maxTempAt2m"@en; ; , "NC" . a rdf:Property; rdfs:comment """The minimum air temperature at 2 metres above ground level during the corresponding time interval. Note: This time series is intended for datasets providing minimum temperature directly, for example daily minimum temperature. It is not required when the minimum can appropriately be derived from tempAt2m."""; ; rdfs:domain ; rdfs:label "minTempAt2m"@en; ; , "NC" . a rdf:Property; rdfs:comment """The population-weighted air temperature at 2 metres above ground level for the corresponding time interval. Note: The value is derived by spatially weighting the air temperature within the represented area by the population distribution. It may be used for modelling temperature-dependent energy consumption, including heating and cooling demand. The population dataset and weighting method are identified through the applicable provenance information."""; ; rdfs:domain ; rdfs:label "populationWeightedTempAt2m"@en; ; , "NC" . a rdf:Property; rdfs:comment "The potential evaporation during the corresponding time interval, expressed as an equivalent depth of water."; ; rdfs:domain ; rdfs:label "potentialEvaporation"@en; ; , "NC" . a rdf:Property; rdfs:comment """The total precipitation received during the corresponding time interval. Note: The value represents accumulated precipitation expressed as an equivalent depth of water."""; ; rdfs:domain ; rdfs:label "precipitation"@en; ; , "NC" . a rdf:Property; rdfs:comment """The amount of liquid precipitation received during the corresponding time interval. Note: The value represents accumulated rainfall expressed as an equivalent depth of water."""; ; rdfs:domain ; rdfs:label "rainfall"@en; ; , "NC" . a rdf:Property; rdfs:comment "The relative humidity at 2 metres above ground level for the corresponding time interval."; ; rdfs:domain ; rdfs:label "relativeHumidityAt2m"@en; ; , "NC" . a rdf:Property; rdfs:comment "The runoff during the corresponding time interval, expressed as an equivalent depth of water over the area."; ; rdfs:domain ; rdfs:label "runoff"@en; ; , "NC" . a rdf:Property; rdfs:comment """The direction of the sea-water current for the corresponding time interval. Note: Current direction normally identifies the direction towards which the water is moving, unlike meteorological wind direction, which identifies the direction from which the wind originates."""; ; rdfs:domain ; rdfs:label "seaCurrentDirection"@en; ; , "NC" . a rdf:Property; rdfs:comment """The speed of the sea-water current for the corresponding time interval. Note: The applicable depth or vertical reference is defined by the source dataset or provenance information."""; ; rdfs:domain ; rdfs:label "seaCurrentSpeed"@en; ; , "NC" . a rdf:Property; rdfs:comment """The proportion of the sea surface covered by sea ice for the corresponding time interval. Note: Sea-ice concentration provides the time-dependent information needed to determine sea-ice presence and extent. It replaces a simple integer seaIce value, which cannot distinguish between partial and complete ice coverage."""; ; rdfs:domain ; rdfs:label "seaIceConcentration"@en; ; , "NC" . a rdf:Property; rdfs:comment "The sea-ice thickness for the corresponding time interval."; ; rdfs:domain ; rdfs:label "seaIceThickness"@en; ; , "NC" . a rdf:Property; rdfs:comment "The sea-surface temperature for the corresponding time interval."; ; rdfs:domain ; rdfs:label "seaSurfaceTemp"@en; ; , "NC" . a rdf:Property; rdfs:comment "The significant wave height for the corresponding time interval."; ; rdfs:domain ; rdfs:label "significantWaveHeight"@en; ; , "NC" . a rdf:Property; rdfs:comment """The amount of water stored in the snowpack at the corresponding time, expressed as an equivalent depth of liquid water. Example: January = 180 mm, March = 430 mm, May = 160 mm, June = 0 mm."""; ; rdfs:domain ; rdfs:label "snowWater"@en; ; , "NC" . a rdf:Property; rdfs:comment "The solid precipitation received during the corresponding time interval, expressed as its equivalent amount of liquid water."; ; rdfs:domain ; rdfs:label "snowfall"@en; ; , "NC" . a rdf:Property; rdfs:comment "The amount of water released by melting snow during the corresponding time interval, expressed as an equivalent depth of liquid water."; ; rdfs:domain ; rdfs:label "snowmelt"@en; ; , "NC" . a rdf:Property; rdfs:comment "The duration of sunshine during the corresponding time interval."; ; rdfs:domain ; rdfs:label "sunshineDuration"@en; ; , "NC" . a rdf:Property; rdfs:comment """The atmospheric pressure at the surface for the corresponding time interval. Note: Surface pressure may be relevant when determining air density for wind-energy calculations."""; ; rdfs:domain ; rdfs:label "surfacePressure"@en; ; , "NC" . a rdf:Property; rdfs:comment "The air temperature at 2 metres above ground level for the corresponding time interval."; ; rdfs:domain ; rdfs:label "tempAt2m"@en; ; , "NC" . a rdf:Property; rdfs:comment "The number of days on which thunder is observed within the corresponding time interval."; ; rdfs:domain ; rdfs:label "thunderDays"@en; ; , "NC" . a rdf:Property; rdfs:comment "The number of nights meeting the applicable tropical-night criterion within the corresponding time interval."; ; rdfs:domain ; rdfs:label "tropicalNights"@en; ; , "NC" . a rdf:Property; rdfs:comment """The direction from which waves propagate for the corresponding time interval. Note: No corresponding normal value is defined because a single average direction may not meaningfully represent a multi-directional sea state."""; ; rdfs:domain ; rdfs:label "waveDirection"@en; ; , "NC" . a rdf:Property; rdfs:comment "The representative wave period for the corresponding time interval."; ; rdfs:domain ; rdfs:label "wavePeriod"@en; ; , "NC" . a rdf:Property; rdfs:comment """The wind direction at 100 metres above ground level for the corresponding time interval. Note: Meteorological wind direction normally identifies the direction from which the wind originates."""; ; rdfs:domain ; rdfs:label "windDirectionAt100m"@en; ; , "NC" . a rdf:Property; rdfs:comment """The wind direction at 10 metres above ground level for the corresponding time interval. Note: Meteorological wind direction normally identifies the direction from which the wind originates. No corresponding normal attribute is defined because a single average direction may be misleading for multimodal wind regimes."""; ; rdfs:domain ; rdfs:label "windDirectionAt10m"@en; ; , "NC" . a rdf:Property; rdfs:comment """The maximum wind gust at 10 metres above ground level during the corresponding time interval. Note: The time interval over which the gust maximum applies is defined by the associated Schedule and TimePoint."""; ; rdfs:domain ; rdfs:label "windGustAt10m"@en; ; , "NC" . a rdf:Property; rdfs:comment "The wind speed at 100 metres above ground level for the corresponding time interval."; ; rdfs:domain ; rdfs:label "windSpeedAt100m"@en; ; , "NC" . a rdf:Property; rdfs:comment "The wind speed at 10 metres above ground level for the corresponding time interval."; ; rdfs:domain ; rdfs:label "windSpeedAt10m"@en; ; , "NC" . a rdf:Property; "Yes"; rdfs:comment "The climate zone that has this schedule."; rdfs:domain ; ; rdfs:label "ClimateZone"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The climate zone time point of the climate zone schedule."; rdfs:domain ; ; rdfs:label "ClimateZoneTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The climate zone schedule that has climate zone time point. "; rdfs:domain ; ; rdfs:label "ClimateZoneSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment """An index representing the avalanche danger for the corresponding time interval. Note: The applicable avalanche danger methodology and classification are identified through the associated data provenance. The CIM model does not prescribe a particular avalanche danger scale. Where the index represents categorical danger levels, the numerical values shall not be assumed to form a linear scale. Example: Using the European Avalanche Danger Scale: \"1\" (Low), \"2\" (Moderate), \"3\" (Considerable), \"4\" (High), \"5\" (Very high)."""; ; rdfs:domain ; rdfs:label "avalancheDangerIndex"@en; ; , "NC" . a rdf:Property; rdfs:comment "The proportion of the sky covered by cloud for the corresponding time interval."; ; rdfs:domain ; rdfs:label "cloudCover"@en; ; , "NC" . a rdf:Property; rdfs:comment "The dew-point temperature at 2 metres above ground level for the corresponding time interval."; ; rdfs:domain ; rdfs:label "dewPointTempAt2m"@en; ; , "NC" . a rdf:Property; rdfs:comment "The diffuse solar irradiance for the corresponding time interval."; ; rdfs:domain ; rdfs:label "diffuseSolarIrradiance"@en; ; , "NC" . a rdf:Property; rdfs:comment "The direct solar irradiance for the corresponding time interval."; ; rdfs:domain ; rdfs:label "directSolarIrradiance"@en; ; , "NC" . a rdf:Property; rdfs:comment """The Drought Code for the corresponding time interval. Note: The Drought Code is a component of the Canadian Fire Weather Index System representing the moisture condition of deep, compact organic fuel layers. It is particularly useful for representing the cumulative effect of prolonged dry conditions and seasonal drought on wildfire potential. Higher values indicate drier conditions. The attribute is used when the applicable wildfire methodology provides a Drought Code. Example: Values such as \"15\", \"300\" and \"600\" represent progressively drier conditions in the Drought Code scale. No universal low, moderate or high classification is implied by these example values; interpretation is provided by the applicable methodology and provenance."""; ; rdfs:domain ; rdfs:label "droughtCode"@en; ; , "NC" . a rdf:Property; rdfs:comment """The evaporation and evapotranspiration during the corresponding time interval, expressed as an equivalent depth of water. Note: The sign convention, where relevant, is defined by the applicable data specification."""; ; rdfs:domain ; rdfs:label "evaporation"@en; ; , "NC" . a rdf:Property; rdfs:comment """A fire-weather index indicating the meteorological conditions relevant to wildfire danger for the corresponding time interval. Note: The applicable fire-weather index methodology and classification are identified through the associated data provenance. The CIM model does not prescribe a specific wildfire classification. The Canadian Fire Weather Index (FWI) System, as used by European Forest Fire Information System (EFFIS), is one example. In this system, the index combines fuel-moisture and fire-behaviour components derived from temperature, relative humidity, wind speed and precipitation. Higher values indicate conditions increasingly favourable to intense wildfire. Example: Using the EFFIS classification: \"5.0\" (Very low), \"10.0\" (Low), \"15.0\" (Moderate), \"37.77\" (High), \"40.01\" (Very high), \"55.55\" (Extreme)."""; ; rdfs:domain ; rdfs:label "fireWeatherIndex"@en; ; , "NC" . a rdf:Property; rdfs:comment "The number of days with freezing precipitation within the corresponding time interval."; ; rdfs:domain ; rdfs:label "freezingPrecipitationDays"@en; ; , "NC" . a rdf:Property; rdfs:comment "The number of frost days within the corresponding time interval."; ; rdfs:domain ; rdfs:label "frostDays"@en; ; , "NC" . a rdf:Property; rdfs:comment """The global solar irradiance for the corresponding time interval. Note: Global solar irradiance represents the total direct and diffuse solar power incident per unit area on the applicable reference surface. It may be used as an environmental input for applications such as photovoltaic production and thermal rating of overhead conductors. The orientation of the reference surface is defined by the applicable dataset or provenance information."""; ; rdfs:domain ; rdfs:label "globalSolarIrradiance"@en; ; , "NC" . a rdf:Property; rdfs:comment "The number of days on which hail occurs within the corresponding time interval."; ; rdfs:domain ; rdfs:label "hailDays"@en; ; , "NC" . a rdf:Property; rdfs:comment "The number of days occurring as part of a heatwave within the corresponding time interval."; ; rdfs:domain ; rdfs:label "heatwaveDays"@en; ; , "NC" . a rdf:Property; rdfs:comment "The number of days meeting the applicable hot-day criterion within the corresponding time interval."; ; rdfs:domain ; rdfs:label "hotDays"@en; ; , "NC" . a rdf:Property; rdfs:comment """The energy equivalent of natural hydro inflow associated with hydro resources in the ClimateZone during the corresponding time interval. Note: The value represents inflow energy for the interval. For example, a weekly TimePoint may contain the natural hydro inflow energy for that week."""; ; rdfs:domain ; rdfs:label "hydroInflow"@en; ; , "NC" . a rdf:Property; rdfs:comment "The number of days meeting the applicable icing criterion within the corresponding time interval."; ; rdfs:domain ; rdfs:label "icingDays"@en; ; , "NC" . a rdf:Property; rdfs:comment "The number of lightning events per unit area occurring during the corresponding time interval."; ; rdfs:domain ; rdfs:label "lightningDensity"@en; ; , "NC" . a rdf:Property; rdfs:comment """The maximum air temperature at 2 metres above ground level during the corresponding time interval. Note: This time series is intended for datasets providing maximum temperature directly."""; ; rdfs:domain ; rdfs:label "maxTempAt2m"@en; ; , "NC" . a rdf:Property; rdfs:comment """The minimum air temperature at 2 metres above ground level during the corresponding time interval. Note: This time series is intended for datasets providing minimum temperature directly, for example daily minimum temperature. It is not required when the minimum can appropriately be derived from tempAt2m."""; ; rdfs:domain ; rdfs:label "minTempAt2m"@en; ; , "NC" . a rdf:Property; rdfs:comment """The population-weighted air temperature at 2 metres above ground level for the corresponding time interval. Note: The value is derived by spatially weighting the air temperature within the represented area by the population distribution. It may be used for modelling temperature-dependent energy consumption, including heating and cooling demand. The population dataset and weighting method are identified through the applicable provenance information."""; ; rdfs:domain ; rdfs:label "populationWeightedTempAt2m"@en; ; , "NC" . a rdf:Property; rdfs:comment "The potential evaporation during the corresponding time interval, expressed as an equivalent depth of water."; ; rdfs:domain ; rdfs:label "potentialEvaporation"@en; ; , "NC" . a rdf:Property; rdfs:comment """The total precipitation received during the corresponding time interval. Note: The value represents accumulated precipitation expressed as an equivalent depth of water."""; ; rdfs:domain ; rdfs:label "precipitation"@en; ; , "NC" . a rdf:Property; rdfs:comment """The amount of liquid precipitation received during the corresponding time interval. Note: The value represents accumulated rainfall expressed as an equivalent depth of water."""; ; rdfs:domain ; rdfs:label "rainfall"@en; ; , "NC" . a rdf:Property; rdfs:comment "The relative humidity at 2 metres above ground level for the corresponding time interval."; ; rdfs:domain ; rdfs:label "relativeHumidityAt2m"@en; ; , "NC" . a rdf:Property; rdfs:comment "The runoff during the corresponding time interval, expressed as an equivalent depth of water over the area."; ; rdfs:domain ; rdfs:label "runoff"@en; ; , "NC" . a rdf:Property; rdfs:comment """The direction of the sea-water current for the corresponding time interval. Note: Current direction normally identifies the direction towards which the water is moving, unlike meteorological wind direction, which identifies the direction from which the wind originates."""; ; rdfs:domain ; rdfs:label "seaCurrentDirection"@en; ; , "NC" . a rdf:Property; rdfs:comment """The speed of the sea-water current for the corresponding time interval. Note: The applicable depth or vertical reference is defined by the source dataset or provenance information."""; ; rdfs:domain ; rdfs:label "seaCurrentSpeed"@en; ; , "NC" . a rdf:Property; rdfs:comment """The proportion of the sea surface covered by sea ice for the corresponding time interval. Note: Sea-ice concentration provides the time-dependent information needed to determine sea-ice presence and extent. It replaces a simple integer seaIce value, which cannot distinguish between partial and complete ice coverage."""; ; rdfs:domain ; rdfs:label "seaIceConcentration"@en; ; , "NC" . a rdf:Property; rdfs:comment "The sea-ice thickness for the corresponding time interval."; ; rdfs:domain ; rdfs:label "seaIceThickness"@en; ; , "NC" . a rdf:Property; rdfs:comment "The sea-surface temperature for the corresponding time interval."; ; rdfs:domain ; rdfs:label "seaSurfaceTemp"@en; ; , "NC" . a rdf:Property; rdfs:comment "The significant wave height for the corresponding time interval."; ; rdfs:domain ; rdfs:label "significantWaveHeight"@en; ; , "NC" . a rdf:Property; rdfs:comment """The amount of water stored in the snowpack at the corresponding time, expressed as an equivalent depth of liquid water. Example: January = 180 mm, March = 430 mm, May = 160 mm, June = 0 mm."""; ; rdfs:domain ; rdfs:label "snowWater"@en; ; , "NC" . a rdf:Property; rdfs:comment "The solid precipitation received during the corresponding time interval, expressed as its equivalent amount of liquid water."; ; rdfs:domain ; rdfs:label "snowfall"@en; ; , "NC" . a rdf:Property; rdfs:comment "The amount of water released by melting snow during the corresponding time interval, expressed as an equivalent depth of liquid water."; ; rdfs:domain ; rdfs:label "snowmelt"@en; ; , "NC" . a rdf:Property; rdfs:comment "The duration of sunshine during the corresponding time interval."; ; rdfs:domain ; rdfs:label "sunshineDuration"@en; ; , "NC" . a rdf:Property; rdfs:comment """The atmospheric pressure at the surface for the corresponding time interval. Note: Surface pressure may be relevant when determining air density for wind-energy calculations."""; ; rdfs:domain ; rdfs:label "surfacePressure"@en; ; , "NC" . a rdf:Property; rdfs:comment "The air temperature at 2 metres above ground level for the corresponding time interval."; ; rdfs:domain ; rdfs:label "tempAt2m"@en; ; , "NC" . a rdf:Property; rdfs:comment "The number of days on which thunder is observed within the corresponding time interval."; ; rdfs:domain ; rdfs:label "thunderDays"@en; ; , "NC" . a rdf:Property; rdfs:comment "The number of nights meeting the applicable tropical-night criterion within the corresponding time interval."; ; rdfs:domain ; rdfs:label "tropicalNights"@en; ; , "NC" . a rdf:Property; rdfs:comment """The direction from which waves propagate for the corresponding time interval. Note: No corresponding normal value is defined because a single average direction may not meaningfully represent a multi-directional sea state."""; ; rdfs:domain ; rdfs:label "waveDirection"@en; ; , "NC" . a rdf:Property; rdfs:comment "The representative wave period for the corresponding time interval."; ; rdfs:domain ; rdfs:label "wavePeriod"@en; ; , "NC" . a rdf:Property; rdfs:comment """The wind direction at 100 metres above ground level for the corresponding time interval. Note: Meteorological wind direction normally identifies the direction from which the wind originates."""; ; rdfs:domain ; rdfs:label "windDirectionAt100m"@en; ; , "NC" . a rdf:Property; rdfs:comment """The wind direction at 10 metres above ground level for the corresponding time interval. Note: Meteorological wind direction normally identifies the direction from which the wind originates. No corresponding normal attribute is defined because a single average direction may be misleading for multimodal wind regimes."""; ; rdfs:domain ; rdfs:label "windDirectionAt10m"@en; ; , "NC" . a rdf:Property; rdfs:comment """The maximum wind gust at 10 metres above ground level during the corresponding time interval. Note: The time interval over which the gust maximum applies is defined by the associated Schedule and TimePoint."""; ; rdfs:domain ; rdfs:label "windGustAt10m"@en; ; , "NC" . a rdf:Property; rdfs:comment "The wind speed at 100 metres above ground level for the corresponding time interval."; ; rdfs:domain ; rdfs:label "windSpeedAt100m"@en; ; , "NC" . a rdf:Property; rdfs:comment "The wind speed at 10 metres above ground level for the corresponding time interval."; ; rdfs:domain ; rdfs:label "windSpeedAt10m"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "Contingency schedule for a contingecy."; rdfs:domain ; ; rdfs:label "ContingencySchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Contingency which has a contingency schedule."; rdfs:domain ; ; rdfs:label "Contingency"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point that relates to this contingency schedule."; rdfs:domain ; ; rdfs:label "ContingencyTimePoint"@en; ; rdfs:range ; , "NC" . a rdf:Property; "Yes"; rdfs:comment "The contingency schedule that has this time point."; rdfs:domain ; ; rdfs:label "ContingencySchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Set true if must study this contingency."; ; rdfs:domain ; rdfs:label "mustStudy"@en; ; , "NC" . a rdf:Property; rdfs:comment "Probability of occurrence. The allowed value range is [0,100]."; ; rdfs:domain ; rdfs:label "probability"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "Enabling schedule associated to a contingency with remedial action."; rdfs:domain ; ; rdfs:label "GenericEnablingSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:domain ; "none"; rdfs:label "multiplier"@en; ; rdfs:range ; . a rdf:Property; rdfs:domain ; "countPerm2"; rdfs:label "unit"@en; ; rdfs:range ; . a rdf:Property; ; rdfs:domain ; rdfs:label "value"@en; ; . a rdf:Property; "No"; rdfs:comment "Enabling schedule which belongs to the cross border relevant."; rdfs:domain ; ; rdfs:label "GenericEnablingSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The schedule of the control function."; rdfs:domain ; ; rdfs:label "CurrentControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The control function that has this schedule."; rdfs:domain ; ; rdfs:label "CurrentControlFunction"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point of the schedule."; rdfs:domain ; ; rdfs:label "CurrentControlFunctionTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The schedule that has this time point."; rdfs:domain ; ; rdfs:label "CurrentControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Target value for the current that the control function is calculating to achieve by adjusting the operational setting to the controlled equipment."; ; rdfs:domain ; rdfs:label "targetValue"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "The schedule of the control function."; rdfs:domain ; ; rdfs:label "CurrentDroopControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The control function that has this schedule."; rdfs:domain ; ; rdfs:label "CurrentDroopControlFunction"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point of the schedule."; rdfs:domain ; ; rdfs:label "CurrentDroopControlFunctionTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The schedule that has this time point."; rdfs:domain ; ; rdfs:label "CurrentDroopControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Droop in capacitive region. The unit is V/A."; ; rdfs:domain ; rdfs:label "droopCapacitive"@en; ; , "NC" . a rdf:Property; rdfs:comment "Droop in inductive region. The unit is V/A."; ; rdfs:domain ; rdfs:label "droopInductive"@en; ; , "NC" . a rdf:Property; rdfs:comment "Offset in capacitive region."; ; rdfs:domain ; rdfs:label "offsetCapacitive"@en; ; , "NC" . a rdf:Property; rdfs:comment "Offset in capacitive region."; ; rdfs:domain ; rdfs:label "offsetInductive"@en; ; , "NC" . a rdf:Property; rdfs:comment "Setpoint when control is active in capacitive region."; ; rdfs:domain ; rdfs:label "targetValueCapacitive"@en; ; , "NC" . a rdf:Property; rdfs:comment "Setpoint when control is active in inductive region."; ; rdfs:domain ; rdfs:label "targetValueInductive"@en; ; , "NC" . a rdf:Property; rdfs:domain ; "none"; rdfs:label "multiplier"@en; ; rdfs:range ; . a rdf:Property; rdfs:domain ; "A"; rdfs:label "unit"@en; ; rdfs:range ; . a rdf:Property; ; rdfs:domain ; rdfs:label "value"@en; ; . a rdf:Property; "No"; rdfs:comment "The schedule of the control function."; rdfs:domain ; ; rdfs:label "DCActivePowerControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The control function that has this schedule."; rdfs:domain ; ; rdfs:label "DCActivePowerControlFunction"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point of the schedule."; rdfs:domain ; ; rdfs:label "DCActivePowerControlFunctionTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The schedule that has this time point."; rdfs:domain ; ; rdfs:label "DCActivePowerControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Target value for the active power that the control function is calculating to achieve by adjusting the operational setting to the controlled equipment."; ; rdfs:domain ; rdfs:label "targetValue"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "The schedule of the control function."; rdfs:domain ; ; rdfs:label "DCCurrentControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The control function that has this schedule."; rdfs:domain ; ; rdfs:label "DCCurrentControlFunction"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point of the schedule."; rdfs:domain ; ; rdfs:label "DCCurrentControlFunctionTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The schedule that has this time point."; rdfs:domain ; ; rdfs:label "DCCurrentControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Droop constant. The pu value is obtained as D [kV/MW] x Sb / Ubdc. The attribute shall be a positive value."; ; rdfs:domain ; rdfs:label "droop"@en; ; , "NC" . a rdf:Property; rdfs:comment "Compensation constant. Used to compensate for voltage drop when controlling voltage at a distant bus. The attribute shall be a positive value."; ; rdfs:domain ; rdfs:label "droopCompensation"@en; ; , "NC" . a rdf:Property; rdfs:comment "Target value for the current that the control function is calculating to achieve by adjusting the operational setting to the controlled equipment."; ; rdfs:domain ; rdfs:label "targetValue"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "The schedule for DC equivalent injection."; rdfs:domain ; ; rdfs:label "PowerShiftKeySchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The schedule of the control function."; rdfs:domain ; ; rdfs:label "DCExtinctionAngleControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The control function that has this schedule."; rdfs:domain ; ; rdfs:label "DCExtinctionAngleControlFunction"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point of the schedule."; rdfs:domain ; ; rdfs:label "DCExtinctionAngleControlFunctionTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The schedule that has this time point."; rdfs:domain ; ; rdfs:label "DCExtinctionAngleControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Target value for the extinction angle that the control function is calculating to achieve by adjusting the operational setting to the controlled equipment."; ; rdfs:domain ; rdfs:label "targetValue"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "The schedule of the control function."; rdfs:domain ; ; rdfs:label "DCFiringAngleControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The control function that has this schedule."; rdfs:domain ; ; rdfs:label "DCFiringAngleControlFunction"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point of the schedule."; rdfs:domain ; ; rdfs:label "DCFiringAngleControlFunctionTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The schedule that has this time point."; rdfs:domain ; ; rdfs:label "DCFiringAngleControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Target value for the firing angle that the control function is calculating to achieve by adjusting the operational setting to the controlled equipment."; ; rdfs:domain ; rdfs:label "targetValue"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "The Power Shift Key schedule for a DCPole."; rdfs:domain ; ; rdfs:label "PowerShiftKeySchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The schedule of the control function."; rdfs:domain ; ; rdfs:label "DCPulseWidthModulationControlFunctionSchedule"@en; ; rdfs:range ; "NC" . "Yes"; rdfs:comment "The control function that has this schedule."; rdfs:domain ; a rdf:Property; ; rdfs:label "DCPulseWidthModulationControlFunction"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point of the schedule."; rdfs:domain ; ; rdfs:label "DCPulseWidthModulationControlFunctionTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The schedule that has this time point."; rdfs:domain ; ; rdfs:label "DCPulseWidthModulationControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Target value for the pulse width factor that the control function is calculating to achieve by adjusting the operational setting to the controlled equipment."; ; rdfs:domain ; rdfs:label "targetValue"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "The schedule of the control function."; rdfs:domain ; ; rdfs:label "DCVoltageControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The control function that has this schedule."; rdfs:domain ; ; rdfs:label "DCVoltageControlFunction"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point of the schedule."; rdfs:domain ; ; rdfs:label "DCVoltageControlFunctionTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The schedule that has this time point."; rdfs:domain ; ; rdfs:label "DCVoltageControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Target value for the voltage that the control function is calculating to achieve by adjusting the operational setting to the controlled equipment."; ; rdfs:domain ; rdfs:label "targetValue"@en; ; , "NC" . a rdf:Property; "Yes"; rdfs:comment "The enabling schedule which belongs to the enabling timepoint."; rdfs:domain ; ; rdfs:label "GenericEnablingSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "It identifies if the element is enabled. True means enabled, False means not enabled."; ; rdfs:domain ; rdfs:label "enabled"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "Generic sequence schedule associated with an energy block order."; rdfs:domain ; ; rdfs:label "GenericSequenceSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The Power Shift Key schedule for an energy block order."; rdfs:domain ; ; rdfs:label "PowerShiftKeySchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The Power Shift Key schedule for an Energy Consumer."; rdfs:domain ; ; rdfs:label "PowerShiftKeySchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The regular schedule for this energy resource group capacity."; rdfs:domain ; ; rdfs:label "EnergyResourceGroupCapacityRegularSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:domain ; ; rdfs:label "EnergyResourceGroupCapacitySchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The Power Shift Key schedule for an energy group capacity."; rdfs:domain ; ; rdfs:label "PowerShiftKeySchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The energy resource group capacity that has a regular schedule."; rdfs:domain ; ; rdfs:label "EnergyResourceGroupCapacity"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The ratio (in percent) between the effective available capacity and the installed capacity over a defined time interval. For weather-dependent resources, the value reflects climate-driven availability as derived from meteorological or hydrological conditions."; ; rdfs:domain ; rdfs:label "availabilityFactor"@en; ; , "NC" . a rdf:Property; rdfs:comment "The weather or condition-dependent active power capacity that is realistically available for operation at a given time. This value reflects reductions due to climatic, hydrological, or operational constraints."; ; rdfs:domain ; rdfs:label "availableCapacityP"@en; ; , "NC" . a rdf:Property; rdfs:comment """The relative weighting used to allocate an aggregate capacity requirement to this energy resource group on a time-series basis. Note: The values provide context-specific top-down capacity allocation weightings and may override normalCapacityAllocationFactor. Each value applies to the corresponding time interval represented by the time-series context. The factors are relative weights and are not required to represent percentages or to sum to 1. The allocation algorithm may normalize or otherwise adjust the applicable factors according to availability, existing capacity and other modelling constraints."""; ; rdfs:domain ; rdfs:label "capacityAllocationFactor"@en; ; , "NC" . a rdf:Property; rdfs:comment "The nominal installed active power capacity of the energy type, independent of weather or operating conditions. This is the maximum technical power rating under standard design assumptions and optimum operation condition."; ; rdfs:domain ; rdfs:label "installedCapacityP"@en; ; , "NC" . a rdf:Property; rdfs:comment "The effective active power capacity for the resource at the specified time, after considering all applied deratings, outages, operational limits, or weather influences. This value represents the usable capacity that can be delivered or consumed, effective capacity."; ; rdfs:domain ; rdfs:label "p"@en; ; , "NC" . a rdf:Property; rdfs:comment "Participation factor for the power group in relation to scheduling area. Must be a positive value."; ; rdfs:domain ; rdfs:label "participationFactor"@en; ; , "NC" . a rdf:Property; "Yes"; rdfs:domain ; ; rdfs:label "EnergyResourceGroupCapacity"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point for this energy resource capacity Schedule."; rdfs:domain ; ; rdfs:label "EnergyResourceGroupCapacityTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The energy resource capacity schedule that has this time point."; rdfs:domain ; ; rdfs:label "EnergyResourceGroupCapacitySchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "The ratio (in percent) between the effective available capacity and the installed capacity over a defined time interval. For weather-dependent resources, the value reflects climate-driven availability as derived from meteorological or hydrological conditions."; ; rdfs:domain ; rdfs:label "availabilityFactor"@en; ; , "NC" . a rdf:Property; rdfs:comment "The weather or condition-dependent active power capacity that is realistically available for operation at a given time. This value reflects reductions due to climatic, hydrological, or operational constraints."; ; rdfs:domain ; rdfs:label "availableCapacityP"@en; ; , "NC" . a rdf:Property; rdfs:comment """The relative weighting used to allocate an aggregate capacity requirement to this energy resource group on a time-series basis. Note: The values provide context-specific top-down capacity allocation weightings and may override normalCapacityAllocationFactor. Each value applies to the corresponding time interval represented by the time-series context. The factors are relative weights and are not required to represent percentages or to sum to 1. The allocation algorithm may normalize or otherwise adjust the applicable factors according to availability, existing capacity and other modelling constraints."""; ; rdfs:domain ; rdfs:label "capacityAllocationFactor"@en; ; , "NC" . a rdf:Property; rdfs:comment "The nominal installed active power capacity of the energy type, independent of weather or operating conditions. This is the maximum technical power rating under standard design assumptions and optimum operation condition."; ; rdfs:domain ; rdfs:label "installedCapacityP"@en; ; , "NC" . a rdf:Property; rdfs:comment "The effective active power capacity for the resource at the specified time, after considering all applied deratings, outages, operational limits, or weather influences. This value represents the usable capacity that can be delivered or consumed, effective capacity."; ; rdfs:domain ; rdfs:label "p"@en; ; , "NC" . a rdf:Property; rdfs:comment "Participation factor for the power group in relation to scheduling area. Must be a positive value."; ; rdfs:domain ; rdfs:label "participationFactor"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "The power shift key schedule for an energy source."; rdfs:domain ; ; rdfs:label "PowerShiftKeySchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "Power shift key schedule associated with an equivalent injection."; rdfs:domain ; ; rdfs:label "PowerShiftKeySchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The power shift key schedule for an external network injection."; rdfs:domain ; ; rdfs:label "PowerShiftKeySchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:domain ; "none"; rdfs:label "multiplier"@en; ; rdfs:range ; . a rdf:Property; rdfs:domain ; "Hz"; rdfs:label "unit"@en; ; rdfs:range ; . a rdf:Property; ; rdfs:domain ; rdfs:label "value"@en; ; . a rdf:Property; "No"; rdfs:comment "The schedule of the control function."; rdfs:domain ; ; rdfs:label "FrequencyControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The control function that has this schedule."; rdfs:domain ; ; rdfs:label "FrequencyControlFunction"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point of the schedule."; rdfs:domain ; ; rdfs:label "FrequencyControlFunctionTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The schedule that has this time point."; rdfs:domain ; ; rdfs:label "FrequencyControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Frequency bias that the control function is using to achieve by adjusting the operational setting to the controlled equipment."; ; rdfs:domain ; rdfs:label "frequencyBias"@en; ; , "NC" . a rdf:Property; rdfs:comment "Target value for the frequency that the control function is calculating to achieve by adjusting the operational setting to the controlled equipment."; ; rdfs:domain ; rdfs:label "targetValue"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "The fuel storage schedule for this fuel storage."; rdfs:domain ; ; rdfs:label "FuelStorageSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Fuel storgae of this fuel storage schedule."; rdfs:domain ; ; rdfs:label "FuelStorage"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point that relates to this fuel storage schedule."; rdfs:domain ; ; rdfs:label "FuelStorageTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The fuel storage schedule that has this time point."; rdfs:domain ; ; rdfs:label "FuelStorageSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Amount of energy available in the storage."; ; rdfs:domain ; rdfs:label "energyStorage"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "Enabling schedule associated to a function block."; rdfs:domain ; ; rdfs:label "GenericEnablingSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "Enabling schedule associated to a gate input pin."; rdfs:domain ; ; rdfs:label "GenericEnablingSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The Power Shift Key schedule for a Generating Unit."; rdfs:domain ; ; rdfs:label "PowerShiftKeySchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "Unit cost schedule associated with a generating unit."; rdfs:domain ; ; rdfs:label "UnitCostSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The availability timepoint for an available schedule."; rdfs:domain ; ; rdfs:label "AvailabilityTimePoint"@en; ; rdfs:range ; "NC", . a rdf:Property; "Yes"; rdfs:comment "Remedial action which has available schedules."; rdfs:domain ; ; rdfs:label "RemedialAction"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Assessed element with contingency that has enabling schedules."; rdfs:domain ; ; rdfs:label "AssessedElementWithContingency"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Assessed element with remedial action that has enabling schedules."; rdfs:domain ; ; rdfs:label "AssessedElementWithRemedialAction"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Automation function which has enabling schedules."; rdfs:domain ; ; rdfs:label "AutomationFunction"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Contingency with remedial action which has enabling schedules."; rdfs:domain ; ; rdfs:label "ContingencyWithRemedialAction"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Cross border relevant that has enabling schedules."; rdfs:domain ; ; rdfs:label "CrossBorderRelevance"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The enabling timepoint for a assessed element with enabling schedule."; rdfs:domain ; ; rdfs:label "EnablingTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Function block which has enabling schedules."; rdfs:domain ; ; rdfs:label "FunctionBlock"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Gate input pin that has a schedule."; rdfs:domain ; ; rdfs:label "GateInputPin"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Power transfer corridor which has generic enabling schedules."; rdfs:domain ; ; rdfs:label "PowerTransferCorridor"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Remedial action dependency which has enabling schedules."; rdfs:domain ; ; rdfs:label "RemedialActionDependency"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Energy block order which has generic sequence schedules."; rdfs:domain ; ; rdfs:label "EnergyBlockOrder"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The sequence timepoint for a sequence schedule."; rdfs:domain ; ; rdfs:label "SequenceTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "Value for the point in time."; rdfs:domain ; ; rdfs:label "GenericValueTimePoint"@en; ; rdfs:range ; "NC", . a rdf:Property; "Yes"; rdfs:comment "Range constraint for the generic value schedule."; rdfs:domain ; ; rdfs:label "RangeConstraint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Time series the time point values belongs to."; rdfs:domain ; ; rdfs:label "GenericValueSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "The value at the time. The meaning of the value is defined by the derived type of the associated schedule. The value can be integer, float or boolean. In case of boolean 1.0 equals true and 0.0 equals false. In case of integer the 0 should be included as a decimal, e.g. 2.0."; ; rdfs:domain ; rdfs:label "value"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "The regular schedule for this grid power capacity."; rdfs:domain ; ; rdfs:label "GridPowerCapacityRegularSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "Grid Power Capacity schedule which contains information on the referred bidding zone."; rdfs:domain ; ; rdfs:label "GridPowerCapacitySchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The grid power capacity that has a regular schedule."; rdfs:domain ; ; rdfs:label "GridPowerCapacity"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "Maximum total active power (AC and DC) that the net position for the bidding zone can have to maintain operational security. Positive sign means flow into the bidding zone."; ; rdfs:domain ; rdfs:label "maxInterchange"@en; ; , "NC" . a rdf:Property; rdfs:comment "Minimum imported active power requirement."; ; rdfs:domain ; rdfs:label "minImportP"@en; ; , "NC" . a rdf:Property; rdfs:comment "Minimum total active power (AC and DC) that the net position for the bidding zone can have to maintain operational security. Negative sign means flow out of the bidding zone."; ; rdfs:domain ; rdfs:label "minInterchange"@en; ; , "NC" . a rdf:Property; rdfs:comment "The netted aggregation of all AC external schedules of an area. Positive sign means flow into the area (Import)."; ; rdfs:domain ; rdfs:label "netACInterchange"@en; ; , "NC" . a rdf:Property; rdfs:comment "The area AC Net Position tolerance."; ; rdfs:domain ; rdfs:label "netACInterchangeTolerance"@en; ; , "NC" . a rdf:Property; rdfs:comment "The netted aggregation of all DC external schedules of an area. Positive sign means flow into the area."; ; rdfs:domain ; rdfs:label "netDCInterchange"@en; ; , "NC" . a rdf:Property; rdfs:comment "The balancing capacity allocated for regulating down, by decreasing the production, increasing the direct current export, decreasing direct current import or increasing the consumption of energy in the bidding zone. This must be a positive number."; ; rdfs:domain ; rdfs:label "regulatingDownAllocation"@en; ; , "NC" . a rdf:Property; rdfs:comment "The balancing capacity allocated for regulating up, by increasing the production, decreasing the direct current export, increasing direct current import or reducing the consumption of energy in the bidding zone. This must be a positive number."; ; rdfs:domain ; rdfs:label "regulatingUpAllocation"@en; ; , "NC" . a rdf:Property; "Yes"; rdfs:comment "Grid Power Capacity which is referred by the capacity schedule."; rdfs:domain ; ; rdfs:label "GridPowerCapacity"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The capacity timepoint for a capacity schedule."; rdfs:domain ; ; rdfs:label "GridPowerCapacityTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The capacity schedule which belongs to the capacity timepoint."; rdfs:domain ; ; rdfs:label "GridPowerCapacitySchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Maximum total active power (AC and DC) that the net position for the bidding zone can have to maintain operational security. Positive sign means flow into the bidding zone."; ; rdfs:domain ; rdfs:label "maxInterchange"@en; ; , "NC" . a rdf:Property; rdfs:comment "Minimum imported active power requirement."; ; rdfs:domain ; rdfs:label "minImportP"@en; ; , "NC" . a rdf:Property; rdfs:comment "Minimum total active power (AC and DC) that the net position for the bidding zone can have to maintain operational security. Negative sign means flow out of the bidding zone."; ; rdfs:domain ; rdfs:label "minInterchange"@en; ; , "NC" . a rdf:Property; rdfs:comment "The netted aggregation of all AC external schedules of an area. Positive sign means flow into the area (Import)."; ; rdfs:domain ; rdfs:label "netACInterchange"@en; ; , "NC" . a rdf:Property; rdfs:comment "The area AC Net Position tolerance."; ; rdfs:domain ; rdfs:label "netACInterchangeTolerance"@en; ; , "NC" . a rdf:Property; rdfs:comment "The netted aggregation of all DC external schedules of an area. Positive sign means flow into the area."; ; rdfs:domain ; rdfs:label "netDCInterchange"@en; ; , "NC" . a rdf:Property; rdfs:comment "The balancing capacity allocated for regulating down, by decreasing the production, increasing the direct current export, decreasing direct current import or increasing the consumption of energy in the bidding zone. This must be a positive number."; ; rdfs:domain ; rdfs:label "regulatingDownAllocation"@en; ; , "NC" . a rdf:Property; rdfs:comment "The balancing capacity allocated for regulating up, by increasing the production, decreasing the direct current export, increasing direct current import or reducing the consumption of energy in the bidding zone. This must be a positive number."; ; rdfs:domain ; rdfs:label "regulatingUpAllocation"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "Grid state alteration schedule associated with a grid state alteration."; rdfs:domain ; ; rdfs:label "GridStateAlterationSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Grid state alteration which has grid state alteration schedules."; rdfs:domain ; ; rdfs:label "GridStateAlteration"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "Grid state alteration time point that relates to this grid state alteration schedule."; rdfs:domain ; ; rdfs:label "GridStateAlterationTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Grid state alteration schedule that has time point."; rdfs:domain ; ; rdfs:label "GridStateAlterationSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "The status of the GridStateAlteration set by an operation or by a signal resulting from a control action."; ; rdfs:domain ; rdfs:label "enabled"@en; ; , "NC" . a rdf:Property; rdfs:comment """Participation factor describing the entity part of the active power provided by a collection of entities (e.g. an active power forecast to a collection of entities is divided to each of the member entity according to the participation factor). Must be a positive value. In the case of a sharing strategy, the distribution is following entities value (V) equals aggregated value (T) divided by sum of participation factors (PF), i.e. V=T/sum(PF). In the case of priority strategy, the item with the lowest number gets allocated energy first. e.g. If 0 this grid alteration does not participate. The sum of all participation factors for all grid state alterations associated with same remedial action shall be equal to 100%."""; ; rdfs:domain ; rdfs:label "participationFactor"@en; ; , "NC" . a rdf:Property; rdfs:comment "The kind of value1 and value2 of the associated IrregularIntervalSchedule."; rdfs:domain ; rdfs:label "valueKind"@en; ; rdfs:range ; , "NC" . a rdf:Property; "No"; rdfs:comment "Base regulat interval schedule which belongs to an hour pattern."; rdfs:domain ; ; rdfs:label "BaseRegularIntervalSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "Hour period which belongs to an hour pattern."; rdfs:domain ; ; rdfs:label "HourPeriod"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "Type of energy demand that the pattern is valid for."; rdfs:domain ; rdfs:label "energyDemandKind"@en; ; rdfs:range ; , "NC" . a rdf:Property; rdfs:comment "Type of peak or intensity that the pattern is valid for."; rdfs:domain ; rdfs:label "peakKind"@en; ; rdfs:range ; , "NC" . a rdf:Property; "Yes"; rdfs:comment "HourPattern which has some hour periods."; rdfs:domain ; ; rdfs:label "HourPattern"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "Time the period end and not including, e.g. 13:00 which means it does not include the time of 13:00 but 12:59."; ; rdfs:domain ; rdfs:label "endTime"@en; ; , "NC" . a rdf:Property; rdfs:comment """Master resource identifier issued by a model authority. The mRID is unique within an exchange context. Global uniqueness is easily achieved by using a UUID, as specified in RFC 4122, for the mRID. The use of UUID is strongly recommended. For CIMXML data files in RDF syntax conforming to IEC 61970-552, the mRID is mapped to rdf:ID or rdf:about attributes that identify CIM object elements."""; ; rdfs:domain ; rdfs:label "mRID"@en; ; , "NC" . a rdf:Property; rdfs:comment "Time the period start and including, e.g. 12:00 which means it include the time of 12:00."; ; rdfs:domain ; rdfs:label "startTime"@en; ; , "NC" . a rdf:Property; rdfs:domain ; "none"; rdfs:label "multiplier"@en; ; rdfs:range ; . a rdf:Property; rdfs:domain ; "h"; rdfs:label "unit"@en; ; rdfs:range ; . a rdf:Property; ; rdfs:domain ; rdfs:label "value"@en; ; . a rdf:Property; "No"; rdfs:comment "The Power Shift Key schedule for a Hydro Pump."; rdfs:domain ; ; rdfs:label "PowerShiftKeySchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The description is a free human readable text describing or naming the object. It may be non unique and may not correlate to a naming hierarchy."; ; rdfs:domain ; rdfs:label "description"@en; ; . a rdf:Property; rdfs:comment """Master resource identifier issued by a model authority. The mRID is unique within an exchange context. Global uniqueness is easily achieved by using a UUID, as specified in RFC 4122, for the mRID. The use of UUID is strongly recommended. For CIMXML data files in RDF syntax conforming to IEC 61970-552, the mRID is mapped to rdf:ID or rdf:about attributes that identify CIM object elements."""; ; rdfs:domain ; rdfs:label "mRID"@en; ; . a rdf:Property; rdfs:comment "The name is any free human readable and possibly non unique text naming the object."; ; rdfs:domain ; rdfs:label "name"@en; ; . a rdf:Property; rdfs:domain ; "none"; rdfs:label "multiplier"@en; ; rdfs:range ; . a rdf:Property; rdfs:domain ; "ohm"; rdfs:label "unit"@en; ; rdfs:range ; . a rdf:Property; ; rdfs:domain ; rdfs:label "value"@en; ; . a rdf:Property; "No"; rdfs:comment "The schedule of the control function."; rdfs:domain ; ; rdfs:label "ImpedanceControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The control function that has this schedule."; rdfs:domain ; ; rdfs:label "ImpedanceControlFunction"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point of the schedule."; rdfs:domain ; ; rdfs:label "ImpedanceControlFunctionTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The schedule that has this time point."; rdfs:domain ; ; rdfs:label "ImpedanceControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Target value for the impedance that the control function is calculating to achieve by adjusting the operational setting to the controlled equipment."; ; rdfs:domain ; rdfs:label "targetValue"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "Infeed limit schedule associated with an infeed limit."; rdfs:domain ; ; rdfs:label "InfeedLimitSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Infeed limit which has infeed limit schedule."; rdfs:domain ; ; rdfs:label "InfeedLimit"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "Infeed limit time point that relates to this infeed limit schedule."; rdfs:domain ; ; rdfs:label "InfeedLimitTimePoint"@en; ; rdfs:range ; , "NC" . a rdf:Property; "Yes"; rdfs:comment "Infeed limit schedule that has time point."; rdfs:domain ; ; rdfs:label "InfeedLimitSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Value of current limit. The attribute shall be a positive value or zero."; ; rdfs:domain ; rdfs:label "valueA"@en; ; , "NC" . a rdf:Property; rdfs:comment "Value of active power limit. The attribute shall be a positive value or zero."; ; rdfs:domain ; rdfs:label "valueW"@en; ; , "NC" . a rdf:Property; rdfs:domain ; "none"; rdfs:label "multiplier"@en; ; rdfs:range ; . a rdf:Property; rdfs:domain ; "WPerm2"; rdfs:label "unit"@en; ; rdfs:range ; . a rdf:Property; ; rdfs:domain ; rdfs:label "value"@en; ; . a rdf:Property; rdfs:domain ; "none"; rdfs:label "multiplier"@en; ; rdfs:range ; . a rdf:Property; rdfs:domain ; "m"; rdfs:label "unit"@en; ; rdfs:range ; . a rdf:Property; ; rdfs:domain ; rdfs:label "value"@en; ; . a rdf:Property; rdfs:domain ; "none"; rdfs:label "multiplier"@en; ; rdfs:range ; . a rdf:Property; rdfs:domain ; "none"; rdfs:label "unit"@en; ; rdfs:range ; . a rdf:Property; ; rdfs:domain ; rdfs:label "value"@en; ; . a rdf:Property; "Yes"; rdfs:comment "The Power Shift Key schedule which belongs to the participation factor timepoint."; rdfs:domain ; ; rdfs:label "PowerShiftKeySchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment """Participation factor describing the entity part of the active power provided by a collection of entities (e.g. an active power forecast to a collection of entities is divided to each of the member entity according to the participation factor). Must be a positive value. In the case of a sharing strategy, the distribution is following entities value (V) equals aggregated value (T) divided by sum of participation factors (PF), i.e. V=T/sum(PF). In the case of priority strategy, the item with the lowest number gets allocated energy first."""; ; rdfs:domain ; rdfs:label "participationFactor"@en; ; , "NC" . a rdf:Property; rdfs:comment """The kind of temporal or operational constraint defined between the dependee and the dependent. Note: Certain dependency constraint kinds may require or prohibit the use of temporal constraint attributes, depending on the semantics of the specialization."""; rdfs:domain ; rdfs:label "constraintKind"@en; ; rdfs:range ; , "NC" . a rdf:Property; rdfs:comment "The duration constraining the next finish or deactivation of the dependent relative to the latest applicable finish or deactivation of the dependee."; ; rdfs:domain ; rdfs:label "finishToFinishLag"@en; ; , "NC" . a rdf:Property; rdfs:comment """Specifies whether finishToFinishLag is an exact, minimum, or maximum temporal constraint. Note: This attribute shall be specified when finishToFinishLag is provided. Example: finishToFinishLag = 2D1H30M is interpreted together with finishToFinishLagKind: - exact: the dependent finishes exactly 2 days, 1 hour and 30 minutes after the latest applicable finish of the dependee. - minimum: the dependent may finish no earlier than 2 days, 1 hour and 30 minutes after the latest applicable finish of the dependee. - maximum: the dependent shall finish no later than 2 days, 1 hour and 30 minutes after the latest applicable finish of the dependee. In all cases, the dependee finish remains applicable only while the dependee remains in the state resulting from that finish. If the dependee subsequently changes state before the dependent finishes, the applicability of the previous finish is re-evaluated."""; rdfs:domain ; rdfs:label "finishToFinishLagKind"@en; ; rdfs:range ; , "NC" . a rdf:Property; rdfs:comment "The duration constraining the next start or activation of the dependent relative to the latest applicable finish or deactivation of the dependee."; ; rdfs:domain ; rdfs:label "finishToStartLag"@en; ; , "NC" . a rdf:Property; rdfs:comment """Specifies whether finishToStartLag is an exact, minimum, or maximum temporal constraint. Note: This attribute shall be specified when finishToStartLag is provided. Example: finishToStartLag = 20M is interpreted together with finishToStartLagKind: - exact: the dependent starts exactly 20 minutes after the latest applicable finish of the dependee. - minimum: the dependent may start no earlier than 20 minutes after the latest applicable finish of the dependee. - maximum: the dependent shall start no later than 20 minutes after the latest applicable finish of the dependee. In all cases, the dependee finish remains applicable only while the dependee remains in the state resulting from that finish. If the dependee subsequently changes state before the dependent starts, the constraint is evaluated from the next applicable finish of the dependee."""; rdfs:domain ; rdfs:label "finishToStartLagKind"@en; ; rdfs:range ; , "NC" . a rdf:Property; rdfs:comment """Master resource identifier issued by a model authority. The mRID is unique within an exchange context. Global uniqueness is easily achieved by using a UUID, as specified in RFC 4122, for the mRID. The use of UUID is strongly recommended. For CIMXML data files in RDF syntax conforming to IEC 61970-552, the mRID is mapped to rdf:ID or rdf:about attributes that identify CIM object elements."""; ; rdfs:domain ; rdfs:label "mRID"@en; ; , "NC" . a rdf:Property; rdfs:comment "The duration constraining the period for which the dependee and dependent are simultaneously active or effective."; ; rdfs:domain ; rdfs:label "overlap"@en; ; , "NC" . a rdf:Property; rdfs:comment """Specifies whether overlap is an exact, minimum, or maximum duration of simultaneous activity or effectiveness. Note: This attribute shall be specified when overlap is provided. Example: overlap = 1H28M45S is interpreted together with overlapKind: - exact: the dependee and dependent are simultaneously active or effective for exactly 1 hour, 28 minutes, and 45 seconds. - minimum: the dependee and dependent shall be simultaneously active or effective for at least 1 hour, 28 minutes, and 45 seconds. - maximum: the dependee and dependent shall be simultaneously active or effective for no more than 1 hour, 28 minutes, and 45 seconds. Unlike the lag attributes, overlap constrains the duration of a simultaneous state rather than the temporal separation between two state transitions."""; rdfs:domain ; rdfs:label "overlapKind"@en; ; rdfs:range ; , "NC" . a rdf:Property; rdfs:comment "The duration constraining the next start or activation of the dependent relative to the latest applicable start or activation of the dependee."; ; rdfs:domain ; rdfs:label "startToStartLag"@en; ; , "NC" . a rdf:Property; rdfs:comment """Specifies whether startToStartLag is an exact, minimum, or maximum temporal constraint. Note: This attribute shall be specified when startToStartLag is provided. Example: startToStartLag = 2H is interpreted together with startToStartLagKind: - exact: the dependent starts exactly 2 hours after the latest applicable start of the dependee. - minimum: the dependent may start no earlier than 2 hours after the latest applicable start of the dependee. - maximum: the dependent shall start no later than 2 hours after the latest applicable start of the dependee. In all cases, the dependee start remains applicable only while the dependee remains in the state resulting from that start. If the dependee subsequently changes state before the dependent starts, the constraint is evaluated from the next applicable start of the dependee."""; rdfs:domain ; rdfs:label "startToStartLagKind"@en; ; rdfs:range ; , "NC" . a rdf:Property; rdfs:domain ; "none"; rdfs:label "multiplier"@en; ; rdfs:range ; . a rdf:Property; rdfs:domain ; "none"; rdfs:label "unit"@en; ; rdfs:range ; . a rdf:Property; rdfs:comment "Normally 0 to 100 on a defined base."; ; rdfs:domain ; rdfs:label "value"@en; ; . a rdf:Property; "No"; rdfs:comment "The schedule of the control function."; rdfs:domain ; ; rdfs:label "PhaseControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The control function that has this schedule."; rdfs:domain ; ; rdfs:label "PhaseControlFunction"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point of the schedule."; rdfs:domain ; ; rdfs:label "PhaseControlFunctionTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The schedule that has this time point."; rdfs:domain ; ; rdfs:label "PhaseControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Target value for the phase that the control function is calculating to achieve by adjusting the operational setting to the controlled equipment."; ; rdfs:domain ; rdfs:label "targetValue"@en; ; , "NC" . a rdf:Property; "Yes"; rdfs:comment "The power bid schedule upon which the dependent power bid schedule depends."; rdfs:domain ; ; rdfs:label "DependeePowerBidSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The power bid schedule whose activation, deactivation, or execution is constrained by the dependee power bid schedule."; rdfs:domain ; ; rdfs:label "DependentPowerBidSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The power bid dependency in which this power bid schedule is the dependee."; rdfs:domain ; ; rdfs:label "DependencyAsDependee"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The power bid dependency in which this power bid schedule is the dependent."; rdfs:domain ; ; rdfs:label "DependencyAsDependent"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "Power bid schedule time points which belong to a power bid schedule."; rdfs:domain ; ; rdfs:label "PowerBidScheduleTimePoint"@en; ; rdfs:range ; "NC", . a rdf:Property; "Yes"; rdfs:comment "Power remedial action for which the bid is given."; rdfs:domain ; ; rdfs:label "PowerRemedialAction"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "Distribution of the power bid amongst the power shift keys."; rdfs:domain ; ; rdfs:label "PowerShiftKeyDistribution"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Schedule resource which has several power bid schedules."; rdfs:domain ; ; rdfs:label "ScheduleResource"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "Cost to activate the bid."; ; rdfs:domain ; rdfs:label "activationCost"@en; ; , "NC" . a rdf:Property; rdfs:comment "Currency of the bid."; rdfs:domain ; rdfs:label "currency"@en; ; rdfs:range ; , "NC" . a rdf:Property; rdfs:comment "Define the direction of the energy adjustment."; rdfs:domain ; rdfs:label "direction"@en; ; rdfs:range ; , "NC" . a rdf:Property; rdfs:comment "Indicates if the power bid schedule is fixed, meaning that all the different power bid schedule values need to be taken without changes. e.g. It is a take-it-or-leave-it bid offer."; ; rdfs:domain ; rdfs:label "isFixed"@en; ; , "NC" . a rdf:Property; rdfs:comment "Indicates if the power bid is an offer or not. True, means that the bid is an offer. False, means that the bid is not an offer."; ; rdfs:domain ; rdfs:label "isOffer"@en; ; , "NC" . a rdf:Property; rdfs:comment "Time it takes for the bid to be called upon until it is active."; ; rdfs:domain ; rdfs:label "leadTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Maximum decrease of the active power change from one time point to the next."; ; rdfs:domain ; rdfs:label "maxRampDownP"@en; ; , "NC" . a rdf:Property; rdfs:comment "Maximum increase of the active power change from one time point to the next."; ; rdfs:domain ; rdfs:label "maxRampUpP"@en; ; , "NC" . a rdf:Property; rdfs:comment "Maximum duration the action needs to be remain active after startup. "; ; rdfs:domain ; rdfs:label "maximumUptime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Minimum time interval between activation of the bid involving startup and shutdown. This value overrides any value on the unit."; ; rdfs:domain ; rdfs:label "minimumOffTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Minimum duration the action needs to be remain active after startup. "; ; rdfs:domain ; rdfs:label "minimumUptime"@en; ; , "NC" . a rdf:Property; rdfs:comment "The numeric local priority given to a bid. Lower numeric values will have higher priority."; ; rdfs:domain ; rdfs:label "priority"@en; ; , "NC" . a rdf:Property; rdfs:comment "Total shutdown cost incurred for all the units involved in the bid. This overrides any cost on the specific unit."; ; rdfs:domain ; rdfs:label "shutdownCost"@en; ; , "NC" . a rdf:Property; rdfs:comment "Maximum total energy that can be activated by the bid."; ; rdfs:domain ; rdfs:label "totalMaximumEnergy"@en; ; , "NC" . a rdf:Property; rdfs:comment "Minimum total energy that has to be activated by the bid."; ; rdfs:domain ; rdfs:label "totalMinimumEnergy"@en; ; , "NC" . a rdf:Property; "Yes"; rdfs:comment "Power bid schedule that has many power bid schedule time points."; rdfs:domain ; ; rdfs:label "PowerBidSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "Cost to activate the bid in the given time point."; ; rdfs:domain ; rdfs:label "activationCost"@en; ; , "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Minimum active power given in the time point."; ; rdfs:domain ; rdfs:label "minimumActivationP"@en; ; , "NC" . a rdf:Property; rdfs:comment "Active power injection. Load sign convention is used, i.e. positive sign means flow out from a node."; ; rdfs:domain ; rdfs:label "p"@en; ; , "NC" . a rdf:Property; rdfs:comment "Price given in the time point."; ; rdfs:domain ; rdfs:label "price"@en; ; , "NC" . a rdf:Property; rdfs:comment "Price for reserving the step increment active power."; ; rdfs:domain ; rdfs:label "reservePrice"@en; ; , "NC" . a rdf:Property; rdfs:comment "Total shutdown cost incurred for all the units involved in the bid given in the time point. This overrides any cost on the specific unit."; ; rdfs:domain ; rdfs:label "shutdownCost"@en; ; , "NC" . a rdf:Property; rdfs:comment "The minimum increment that can be applied for an increase in an activation request."; ; rdfs:domain ; rdfs:label "stepIncrementP"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "The Power Shift Key schedule for a Power Electronics Unit."; rdfs:domain ; ; rdfs:label "PowerShiftKeySchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The schedule of the control function."; rdfs:domain ; ; rdfs:label "PowerFactorControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The control function that has this schedule."; rdfs:domain ; ; rdfs:label "PowerFactorControlFunction"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point of the schedule."; rdfs:domain ; ; rdfs:label "PowerFactorControlFunctionTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The schedule that has this time point."; rdfs:domain ; ; rdfs:label "PowerFactorControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Target value for the power factor that the control function is calculating to achieve by adjusting the operational setting to the controlled equipment."; ; rdfs:domain ; rdfs:label "targetValue"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "Power bid schedule addressing the power remedial action."; rdfs:domain ; ; rdfs:label "PowerBidSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "Power remedial action schedule which has a power remedial action."; rdfs:domain ; ; rdfs:label "PowerRemedialActionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Power remedial action for the power remedial action schedule."; rdfs:domain ; ; rdfs:label "PowerRemedialAction"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point that relates to this power remedial action schedule."; rdfs:domain ; ; rdfs:label "PowerRemedialActionTimePoint"@en; ; rdfs:range ; "NC", . a rdf:Property; "Yes"; rdfs:comment "The power remedial action schedule that has this time point."; rdfs:domain ; ; rdfs:label "PowerRemedialActionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Maximum net amount of active power that the remedial action can regulate down."; ; rdfs:domain ; rdfs:label "maxRegulatingDown"@en; ; , "NC" . a rdf:Property; rdfs:comment "Maximum net amount of active power that the remedial action can regulate up."; ; rdfs:domain ; rdfs:label "maxRegulatingUp"@en; ; , "NC" . a rdf:Property; "Yes"; rdfs:comment "Power bid schedule for the given distribution."; rdfs:domain ; ; rdfs:label "PowerBidSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Power Shift Key schedule in power shift key distribution."; rdfs:domain ; ; rdfs:label "PowerShiftKeySchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Power Shift Key Strategy which has a Power Shift Key Distribution."; rdfs:domain ; ; rdfs:label "PowerShiftKeyStrategy"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "DC equivalent injection that has this power shift key schedule."; rdfs:domain ; ; rdfs:label "DCEquivalentInjection"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "A DC Pole which has a Power Shift Key Schedule."; rdfs:domain ; ; rdfs:label "DCPole"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "An energy block order which has a Power Shift Key Schedule."; rdfs:domain ; ; rdfs:label "EnergyBlockOrder"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The EnergyConsumer that has a Power Shift Key schedule."; rdfs:domain ; ; rdfs:label "EnergyConsumer"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The energy group capacity which has a Power Shift Key Schedule."; rdfs:domain ; ; rdfs:label "EnergyResourceGroupCapacity"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The energy source which has a power shift key schedule. The renewable resources should be modelled as PowerElectronicsUnit."; rdfs:domain ; ; rdfs:label "EnergySource"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Equivalent injection which is part of a powoer shift key schedule."; rdfs:domain ; ; rdfs:label "EquivalentInjection"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The energy source which has a power shift key schedule."; rdfs:domain ; ; rdfs:label "ExternalNetworkInjection"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The Generating Unit which has a Power Shift Key Schedule."; rdfs:domain ; ; rdfs:label "GeneratingUnit"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The Hydro Pump which has a Power Shift Key schedule."; rdfs:domain ; ; rdfs:label "HydroPump"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The participation factor timepoint for a Power Shift Key schedule."; rdfs:domain ; ; rdfs:label "ParticipationFactorTimePoint"@en; ; rdfs:range ; "NC", . a rdf:Property; "Yes"; rdfs:comment "The Power Electronics Unit which has a Power Shift Key schedule."; rdfs:domain ; ; rdfs:label "PowerElectronicsUnit"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "Power Shift Key distribution for the Power Shift Key schedule."; rdfs:domain ; ; rdfs:label "PowerShiftKeyDistribution"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The Schedule Resource which has a Power Shift Key schedule."; rdfs:domain ; ; rdfs:label "ScheduleResource"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:domain ; ; rdfs:label "SchedulingArea"@en; ; rdfs:range . a rdf:Property; "No"; rdfs:comment "Power Shift Key Distribution associated to this power shift key strategy."; rdfs:domain ; ; rdfs:label "PowerShiftKeyDistribution"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "Generic enabling schedule associated with a power transfer corridor."; rdfs:domain ; ; rdfs:label "GenericEnablingSchedule"@en; ; rdfs:range ; "NC" . rdfs:domain ; " none"; rdfs:label "multiplier"@en; a rdf:Property; ; rdfs:range ; . a rdf:Property; rdfs:domain ; "Pa"; rdfs:label "unit"@en; ; rdfs:range ; . a rdf:Property; ; rdfs:domain ; rdfs:label "value"@en; ; . a rdf:Property; "No"; rdfs:comment "Generic value schedule which has a range constraint."; rdfs:domain ; ; rdfs:label "GenericValueSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:domain ; "M"; rdfs:label "multiplier"@en; ; rdfs:range ; . a rdf:Property; rdfs:domain ; "VAr"; rdfs:label "unit"@en; ; rdfs:range ; . a rdf:Property; ; rdfs:domain ; rdfs:label "value"@en; ; . a rdf:Property; "No"; rdfs:comment "The schedule of the control function."; rdfs:domain ; ; rdfs:label "ReactivePowerControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The control function that has this schedule."; rdfs:domain ; ; rdfs:label "ReactivePowerControlFunction"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point of the schedule."; rdfs:domain ; ; rdfs:label "ReactivePowerControlFunctionTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The schedule that has this time point."; rdfs:domain ; ; rdfs:label "ReactivePowerControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Target value for the reactive power that the control function is calculating to achieve by adjusting the operational setting to the controlled equipment."; ; rdfs:domain ; rdfs:label "targetValue"@en; ; , "NC" . a rdf:Property; rdfs:domain ; "M"; rdfs:label "multiplier"@en; ; rdfs:range ; . a rdf:Property; rdfs:domain ; "Wh"; rdfs:label "unit"@en; ; rdfs:range ; . a rdf:Property; ; rdfs:domain ; rdfs:label "value"@en; ; . a rdf:Property; "No"; rdfs:comment "Available schedule associated to a remedial action."; rdfs:domain ; ; rdfs:label "GenericAvailableSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "Enabling schedule associated to a remedial action dependency."; rdfs:domain ; ; rdfs:label "GenericEnablingSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "Remedial action group schedule associated with a remedial action group."; rdfs:domain ; ; rdfs:label "RemedialActionGroupSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Remedial action group which has remedial action group schedules."; rdfs:domain ; ; rdfs:label "RemedialActionGroup"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "Remedial action group time point that relates to this remedial action group schedule."; rdfs:domain ; ; rdfs:label "RemedialActionGroupTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Remedial action group schedule that has time point."; rdfs:domain ; ; rdfs:label "RemedialActionGroupSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Maximum net amount of active power that the group of remedial actions can regulate down."; ; rdfs:domain ; rdfs:label "maxRegulatingDown"@en; ; , "NC" . a rdf:Property; rdfs:comment "Maximum net amount of active power that the group of remedial actions can regulate up."; ; rdfs:domain ; rdfs:label "maxRegulatingUp"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "Remedial action scheme schedule that has this armed remedial action."; rdfs:domain ; ; rdfs:label "RemedialActionSchemeSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Armed remedial action for a remedial action scheme."; rdfs:domain ; ; rdfs:label "ArmedRemedialAction"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "Remedial action scheme time point that relates to this remedial action scheme schedule."; rdfs:domain ; ; rdfs:label "RemedialActionSchemeTimePoint"@en; ; rdfs:range ; "NC", . a rdf:Property; "Yes"; rdfs:comment "Remedial action scheme schedule that has time point."; rdfs:domain ; ; rdfs:label "RemedialActionSchemeSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "Defines the arming status of the remedial action scheme. It is set by operation or by signal."; ; rdfs:domain ; rdfs:label "armed"@en; ; , "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Specifies the availability of the Remedial Action Scheme (RAS). If true, the RAS is available for contingency processing. If false, the RAS is treated by contingency processing as if it is not in the model."; ; rdfs:domain ; rdfs:label "inService"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "The reservoir schedule for this reservoir."; rdfs:domain ; ; rdfs:label "ReservoirSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The reservoir that has a schedule."; rdfs:domain ; ; rdfs:label "Reservoir"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point that relates to this reservoir schedule."; rdfs:domain ; ; rdfs:label "ReservoirTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The reservoir schedule that has this time point."; rdfs:domain ; ; rdfs:label "ReservoirSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Amount of energy available in the storage."; ; rdfs:domain ; rdfs:label "energyStorage"@en; ; , "NC" . a rdf:Property; rdfs:domain ; "none"; rdfs:label "multiplier"@en; ; rdfs:range ; . a rdf:Property; rdfs:domain ; "ohm"; rdfs:label "unit"@en; ; rdfs:range ; . a rdf:Property; ; rdfs:domain ; rdfs:label "value"@en; ; . a rdf:Property; "No"; rdfs:comment "Power bid schedule which belongs to a schedule resource."; rdfs:domain ; ; rdfs:label "PowerBidSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The Power Shift Key schedule for a schedule resource."; rdfs:domain ; ; rdfs:label "PowerShiftKeySchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:domain ; ; rdfs:label "PowerShiftKeySchedule"@en; ; rdfs:range . a rdf:Property; "No"; rdfs:comment "Base regular interval schedule which has seasons."; rdfs:domain ; ; rdfs:label "BaseRegularIntervalSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "Date season ends."; ; rdfs:domain ; rdfs:label "endDate"@en; ; . a rdf:Property; rdfs:comment "Date season starts."; ; rdfs:domain ; rdfs:label "startDate"@en; ; . a rdf:Property; rdfs:domain ; "none"; rdfs:label "multiplier"@en; ; rdfs:range ; . a rdf:Property; rdfs:domain ; "s"; rdfs:label "unit"@en; ; rdfs:range ; . a rdf:Property; rdfs:comment "Time, in seconds"; ; rdfs:domain ; rdfs:label "value"@en; ; . a rdf:Property; "Yes"; rdfs:comment "The sequence schedule which belongs to the sequence timepoint."; rdfs:domain ; ; rdfs:label "GenericSequenceSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Sequence needs to be ordered by the scheduling area. It has to be unique by the scheduling area."; ; rdfs:domain ; rdfs:label "sequence"@en; ; , "NC" . a rdf:Property; rdfs:domain ; "none"; rdfs:label "multiplier"@en; ; rdfs:range ; . a rdf:Property; rdfs:domain ; "mPers"; rdfs:label "unit"@en; ; rdfs:range ; . a rdf:Property; ; rdfs:domain ; rdfs:label "value"@en; ; . a rdf:Property; "No"; rdfs:comment "Stage trigger schedule associated with a stage trigger."; rdfs:domain ; ; rdfs:label "StageTriggerSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Stage trigger which has stage trigger schedules."; rdfs:domain ; ; rdfs:label "StageTrigger"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "Stage trigger time point that relates to this remedial action scheme schedule."; rdfs:domain ; ; rdfs:label "StageTriggerTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Stage trigger schedule that has time point."; rdfs:domain ; ; rdfs:label "StageTriggerSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "Defines the arming status of the remedial action scheme. It is set by operation or by signal."; ; rdfs:domain ; rdfs:label "armed"@en; ; , "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Specifies the availability of the Remedial Action Scheme (RAS). If true, the RAS is available for contingency processing. If false, the RAS is treated by contingency processing as if it is not in the model."; ; rdfs:domain ; rdfs:label "inService"@en; ; , "NC" . a rdf:Property; rdfs:domain ; "none"; rdfs:label "multiplier"@en; ; rdfs:range ; . a rdf:Property; rdfs:domain ; "degC"; rdfs:label "unit"@en; ; rdfs:range ; . a rdf:Property; ; rdfs:domain ; rdfs:label "value"@en; ; . a rdf:Property; "Yes"; rdfs:comment "GeneratingUnit which has unit cost schedules."; rdfs:domain ; ; rdfs:label "GeneratingUnit"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The unit cost time point that relates to this unit cost schedule."; rdfs:domain ; ; rdfs:label "UnitCostTimePoint"@en; ; rdfs:range ; , "NC" . a rdf:Property; rdfs:comment "Currency the energy price is given in."; rdfs:domain ; rdfs:label "currency"@en; ; rdfs:range ; , "NC" . a rdf:Property; "Yes"; rdfs:comment "The unit cost schedule that has time point."; rdfs:domain ; ; rdfs:label "UnitCostSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "The shutdown cost incurred for each shutdown of the GeneratingUnit."; ; rdfs:domain ; rdfs:label "shutdownCost"@en; ; , "NC" . a rdf:Property; rdfs:comment "The initial startup cost incurred for each start of the GeneratingUnit."; ; rdfs:domain ; rdfs:label "startupCost"@en; ; , "NC" . a rdf:Property; rdfs:comment "The warm startup cost incurred for each start of the GeneratingUnit."; ; rdfs:domain ; rdfs:label "warmStartupCost"@en; ; , "NC" . a rdf:Property; rdfs:domain ; "k"; rdfs:label "multiplier"@en; ; rdfs:range ; . a rdf:Property; rdfs:domain ; "V"; rdfs:label "unit"@en; ; rdfs:range ; . a rdf:Property; ; rdfs:domain ; rdfs:label "value"@en; ; . a rdf:Property; "No"; rdfs:comment "The schedule of the control function."; rdfs:domain ; ; rdfs:label "VoltageAngleControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The control function that has this schedule."; rdfs:domain ; ; rdfs:label "VoltageAngleControlFunction"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point of the schedule."; rdfs:domain ; ; rdfs:label "VoltageAngleControlFunctionTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The schedule that has this time point."; rdfs:domain ; ; rdfs:label "VoltageAngleControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Target value for the voltage angle that the control function is calculating to achieve by adjusting the operational setting to the controlled equipment."; ; rdfs:domain ; rdfs:label "targetValue"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "Voltage angle schedule associated with a voltage angle limit."; rdfs:domain ; ; rdfs:label "VoltageAngleSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "Voltage angle limit which has voltage angle schedule."; rdfs:domain ; ; rdfs:label "VoltageAngleLimit"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The voltage angle time point that relates to this voltage angle schedule."; rdfs:domain ; ; rdfs:label "VoltageAngletimePoint"@en; ; rdfs:range ; "NC", . a rdf:Property; "Yes"; rdfs:comment "The voltage angle schedule that has time point."; rdfs:domain ; ; rdfs:label "VoltageAngleSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "The difference in angle degrees between referenced by the association end OperationalLimitSet.Terminal and the Terminal referenced by the association end VoltageAngleLimit.AngleReferenceTerminal. The value shall be positive (greater than zero)."; ; rdfs:domain ; rdfs:label "value"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "The schedule of the control function."; rdfs:domain ; ; rdfs:label "VoltageControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The control function that has this schedule."; rdfs:domain ; ; rdfs:label "VoltageControlFunction"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point of the schedule."; rdfs:domain ; ; rdfs:label "VoltageControlFunctionTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The schedule that has this time point."; rdfs:domain ; ; rdfs:label "VoltageControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Target value for the voltage that the control function is calculating to achieve by adjusting the operational setting to the controlled equipment."; ; rdfs:domain ; rdfs:label "targetValue"@en; ; , "NC" . a rdf:Property; "No"; rdfs:comment "The schedule of the control function."; rdfs:domain ; ; rdfs:label "VoltageInjectionControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The control function that has this schedule."; rdfs:domain ; ; rdfs:label "VoltageInjectionControlFunction"@en; ; rdfs:range ; "NC" . a rdf:Property; "No"; rdfs:comment "The time point of the schedule."; rdfs:domain ; ; rdfs:label "VoltageInjectionControlFunctionTimePoint"@en; ; rdfs:range ; "NC" . a rdf:Property; "Yes"; rdfs:comment "The schedule that has this time point."; rdfs:domain ; ; rdfs:label "VoltageInjectionControlFunctionSchedule"@en; ; rdfs:range ; "NC" . a rdf:Property; rdfs:comment "The time the data is valid for."; ; rdfs:domain ; rdfs:label "atTime"@en; ; , "NC" . a rdf:Property; rdfs:comment "Target value for the voltage that the control function is calculating to achieve by adjusting the operational setting to the controlled equipment."; ; rdfs:domain ; rdfs:label "targetValue"@en; ; , "NC" . a ; rdfs:comment "The referenced value is to be met exactly."; rdfs:label "exact"@en; "enum" . a ; rdfs:comment "The referenced value establishes a upper bound."; rdfs:label "maximum"@en; "enum" . a ; rdfs:comment "The referenced value establishes a lower bound."; rdfs:label "minimum"@en; "enum" . a ; rdfs:comment "The network element that is going to be assessed is excluded for being secured by the capacity calculation region."; rdfs:label "capacityCalculationRegion"@en; "enum" . a ; rdfs:comment "The network element that is going to be assessed is excluded for being secured for the native capacity calculation region since it would be secured for a non native capacity calculation region."; rdfs:label "nonNativeCapacityCalculationRegion"@en; "enum" . a ; rdfs:comment "The network element that is going to be assessed is excluded for being secured by the system operator."; rdfs:label "systemOperator"@en; "enum" . a ; rdfs:comment "Linear interpolation is applied for values between two time points."; rdfs:label "linear"@en; "enum" . a ; rdfs:comment "The value between two time points is set to next value."; rdfs:label "next"@en; "enum" . a ; rdfs:comment "No interpolation is applied."; rdfs:label "none"@en; "enum" . a ; rdfs:comment "The value between two time points is set to previous value."; rdfs:label "previous"@en; "enum" . a ; rdfs:comment "Mega 10**6."; rdfs:label "M"@en; "enum" . a ; rdfs:comment "No multiplier or equivalently multiply by 1."; rdfs:label "none"@en; "enum" . a ; rdfs:comment "Current in amperes."; rdfs:label "A"@en; "enum" . a ; rdfs:comment "Frequency in hertz (1/s)."; rdfs:label "Hz"@en; "enum" . a ; rdfs:comment "Electric potential in volts (W/A)."; rdfs:label "V"@en; "enum" . a ; rdfs:comment """Reactive power in volt amperes reactive. The “reactive” or “imaginary” component of electrical power (VIsin(phi)). (See also real power and apparent power). Note: Different meter designs use different methods to arrive at their results. Some meters may compute reactive power as an arithmetic value, while others compute the value vectorially. The data consumer should determine the method in use and the suitability of the measurement for the intended purpose."""; rdfs:label "VAr"@en; "enum" . a ; rdfs:comment "Real power in watts (J/s). Electrical power may have real and reactive components. The real portion of electrical power (I²R or VIcos(phi)), is expressed in Watts. See also apparent power and reactive power."; rdfs:label "W"@en; "enum" . a ; rdfs:comment "Real energy in watt hours."; rdfs:label "Wh"@en; "enum" . a ; rdfs:comment "Plane angle in degrees."; rdfs:label "deg"@en; "enum" . a ; rdfs:comment "Dimension less quantity, e.g. count, per unit, etc."; rdfs:label "none"@en; "enum" . a ; rdfs:comment "Electric resistance in ohms (V/A)."; rdfs:label "ohm"@en; "enum" . a ; rdfs:comment "Time in seconds."; rdfs:label "s"@en; "enum" . a ; rdfs:comment "Value of the range constraint is replacing the attribute value referenced by the PropertyReference in a determined operational scenario."; rdfs:label "absolute"@en; "enum" . a ; rdfs:comment "Value of the range constraint is incrementing the attribute value referenced by the PropertyReference in a determined operational scenario."; rdfs:label "incremental"@en; "enum" . a ; rdfs:comment "Value of the range constraint is incrementing in percentage the attribute value referenced by the PropertyReference in a determined operational scenario. "; rdfs:label "incrementalPercentage"@en; "enum" .